Fagor CNC 8070 - Page 6

Hardware configuration.
CNC 8070
·6·
(REF: 1911)
CHAPTER 11 VERTICAL KEYB / VERTICAL KEYB+MOUSE.
11.1 Specifications. ............................................................................................................. 217
11.2 General diagram. ........................................................................................................ 218
11.3 Dimensions. ................................................................................................................ 219
11.4 Enclosure and mounting of the module. ...................................................................... 220
11.4.1 Enclosure design. .................................................................................................... 220
11.4.2 Securing the module. ............................................................................................... 221
11.5 Power supply for the module. ..................................................................................... 222
11.6 Hardware functionalities. ............................................................................................. 223
11.6.1 Ground connection. ................................................................................................. 223
11.6.2 Rear connectors. ..................................................................................................... 223
11.7 Bus CAN (CANfagor/CANopen protocols)................................................................... 226
11.7.1 Identification of the modules at the bus. .................................................................. 227
11.7.2 Identification of the first and last elements of the bus. Line terminating resistor...... 228
11.7.3 CAN bus type selection (CANfagor/CANopen). ....................................................... 228
11.7.4 Selecting the speed for the CANfagor bus............................................................... 228
11.7.5 Selecting the speed for the CANopen bus............................................................... 228
CHAPTER 12 HORIZONTAL KEYB 2.0 + TOUCHPAD.
12.1 Specifications. ............................................................................................................. 229
12.2 General diagram. ........................................................................................................ 230
12.3 Dimensions. ................................................................................................................ 231
12.4 Enclosure and mounting of the module. ...................................................................... 232
12.4.1 Enclosure design. .................................................................................................... 232
12.4.2 Securing the module. ............................................................................................... 233
12.5 Voltage supply for the module. .................................................................................... 234
12.6 Connectors. ................................................................................................................. 235
12.7 Selecting the language and the keyboard distribution. ................................................ 235
12.8 Using the Fagor logo key. ........................................................................................... 237
12.9 Numeric keypad........................................................................................................... 237
12.10 Touchpad (touch screen). ........................................................................................... 238
CHAPTER 13 OP-PANEL / OP-PANEL+SPDL RATE.
13.1 Specifications. ............................................................................................................. 239
13.2 General diagram. ........................................................................................................ 240
13.3 Dimensions. ................................................................................................................ 241
13.4 Enclosure and mounting of the module. ...................................................................... 242
13.4.1 Enclosure design. .................................................................................................... 242
13.4.2 Securing the module. ............................................................................................... 243
13.5 Power supply for the module. ..................................................................................... 244
13.6 Hardware functionalities. ............................................................................................. 245
13.6.1 Ground connection. ................................................................................................. 245
13.6.2 Rear connectors. ..................................................................................................... 245
13.7 Handwheel connection. ............................................................................................... 249
13.8 Bus CAN (CANfagor/CANopen protocols)................................................................... 250
13.8.1 Identification of the modules at the bus. .................................................................. 251
13.8.2 Identification of the first and last elements of the bus. Line terminating resistor...... 252
13.8.3 CAN bus type selection (CANfagor/CANopen). ....................................................... 252
13.8.4 Selecting the speed for the CANfagor bus............................................................... 252
13.8.5 Selecting the speed for the CANopen bus............................................................... 252
CHAPTER 14 MOUSE MODULE.
14.1 Especificaciones. ........................................................................................................ 253
14.2 Dimensions. ................................................................................................................ 254
CHAPTER 15 EMERGENCY BATTERY (ONLY ETX PLATFORM).
15.1 Battery dimensions. .................................................................................................... 256
15.2 Connectors and connection. ........................................................................................ 257
15.3 Operation of the emergency battery. ........................................................................... 258
CHAPTER 16 CNC-FPS. FAGOR-UPS (Q7-A PLATFORM ONLY).
16.1 Specifications. ............................................................................................................. 260
16.2 Dimensions. ................................................................................................................ 260
16.3 Securing the module.................................................................................................... 261
16.4 Protection fuse. ........................................................................................................... 261
16.5 UPS Connection Diagram............................................................................................ 262