FARGO electronics HDP600 - Page 364

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.3)
16-2
CR-80, CR-90 and CR-100, 7-13, 7-16
CR-90, 15-4
CR-90 or CR-100, 2-29
CSA, 2-6
Cursor, 15-4
Custom 1/Custom 2 options, 7-6, 7-18, 7-19
custom Image Transfer settings., 7-6
customization options, 7-60
D
Darkness, 15-4
DB-9, 15-4
DC (Direct Current), 15-4
DC Motor, 15-4
Decrease/Increase the Print Offset value, 11-7
Default, 15-4
Default button, 7-41
Defined Area(s) check box, 7-50
Defined Area(s) option, 7-48
Defrag, 15-4
Dimensions, 2-9
DIP switches (Dual In-line Package Switches), 15-4
Direct-to-Card (DTC) Printing, 15-5
direct-to-card printing, 7-5
disable printing, 7-37
Display, 2-9
Dither, 15-5
dither method, 7-30
DMA (Direct Memory Access), 15-3
Dongle, 15-5
Dot, 15-5
Dot pitch, 15-5
Download, 15-5
DPI (Dot Per Inch), 15-5
DRAM (Dynamic Random Access Memory), 15-5
DRAM Memory Error, 10-3
Driver, 15-5
Duplex Printing, 15-5
dwell temperature, 7-18
Dwell Time, 7-9, 15-6
Dye Migration, 15-6
Dye-Sub Intensity slide, 7-39
dye-sub printed image, 7-39
Dye-Sublimation, 2-14, 15-6
Dye-Sublimation Cyan Panel, 2-22
Dye-Sublimation Magenta Panel, 2-22
dye-sublimation ribbon Panels, 7-39
Dye-Sublimation Yellow Panel, 2-22
E
E-card, 15-6
E-card Docking Station, 15-6
ECP Mode (Enhanced Capabilities Port Mode), 15-6
edge of card, 11-21
Edge-to-Edge, 15-6
Edge-to-Edge printing, 7-18
EE Checksum Error, 10-2
EE Error, 4-4
EE Memory, 15-6
EE Memory Error, 10-2
EEPROM (Electrically Erasable Programmable Read
Only Memory), 15-6
EEPROM Erased, 4-4
embedded contaminants, 2-23
Emissions Standards, 2-6
Enable MLE Support checkbox, 7-61
Encode Station, 2-19
Encoder (Smart Card), 15-6
Encoder (wheel), 15-7
Encoder Settings, 11-20
encoding instructions, 7-37
Encoding Mode, 7-58, 7-59
Encoding Options, 2-9
End Sentinel (ES)., 7-65
Engine, 15-7
EOF (End Of Form), 15-7
EPP (Enhanced Parallel Port), 15-7
EPROM (Electronically Programmable Read Only
Memory), 15-7
Error/Attention Screens, 2-21
Escape sequence, 15-7
ESD, 1-2, 7-3, 8-3
ESD (ElectroStatic Discharge), 15-7
Ethernet, 15-7
Examine test card, 11-19
F
factory default settings/Default button, 7-45
Failed to verify the encoded mag data., 4-9
Fargo Technical Support, 13-1
Fargo Technical Support via the Web, 13-1
FCC, 2-6
Feeder Station, 2-19
Field Separator (FS), 7-65
Film, 15-7
Film Calibration Fail Error, 4-5
Film Drive adjustment, 11-16
Film is out!, 4-6
Film Sensors are not calibrated., 4-6
Film transfers, 11-17
Firmware, 15-7
Firmware file link, 12-3
Firmware Updater Application Program, 12-1, 12-2
Firmware Updater dialog, 12-4
Firmware Updater window, 12-4
Firmware Updates, 12-2, 12-3, 12-6, 12-7
Firmware Upgrade, 11-29
Flash Memory, 15-8
Flashing GREEN, 2-20
Flip Command Error, 4-6
Font, 15-8
FPGA (Field Programmable Gate Array), 15-8
FPGA error, 10-4
FPGA Load Fail!, 4-6
Full bleed, 15-8
Full Card option, 7-47
Functional Specifications, 2-14
G
Gamma, 15-8