FARGO electronics HDP600 - Page 365

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.3)
16-3
Glossy / Matte, 15-8
Glossy PVC, 15-8
Glossy-PVC or Matte-PVC options, 7-45
Graphical Device Interface (GDI), 15-8
Gray Scale, 15-8
Gray/Align YMC, 11-19
Gray/Align YMCK, 4-17
Guide eject mode, 7-62
H
Halftoning, 15-8
Hard Drive, 15-9
Hardware, 15-9
HDP (High Definition Printing™), 15-9
HDP Cards-Matte PVC + H Panel ribbon
(2)
,
7-6
HDP Cards-Matte PVC + non-H Panel ribbon, 7-6
HDP Film, 7-45
HDP Film Options, 2-10
HDP Film particles, 7-9
HDP Film Storage Temperature, 2-10
HDP Film transfer parameters, 7-5
HDP710 Gray/Align YMC/K for HDP600, 4-17
Head, 15-9
Head Lift Error, Transfer Roller Lift Error, Card Stack
Lift Error, 4-9
Head Resistance Error, 4-7
Head Thermistor, 4-5
Head Voltage Error, 4-7
Heat Seal, 7-5, 15-9
Heat sink, 15-9
Heater Timeout, 4-5
HiCo (High Coercivity), 15-9
High Coercivity, 7-58
High Coercivity UltraCard IIIs, 7-58, 7-59
high-coercivity Magnetic Stripes, 7-56
holographic-type overlaminates, 2-29
Hopper Blocked Error, 4-7
Hopper Jam Error, 4-7
Horizontal adjustment, 7-44
HTML (HyperText Markup Language), 15-9
HTTP (HyperText Transfer Protocol), 15-9
Humidity, 2-10
I
IC (Integrated Circuit), 15-9
IC smart cards/proximity cards, 7-5
ID (Identification), 15-9
ID format, 7-31
ID software applications, 7-65
IEEE 1284 (Institute of Electrical and Electronics
Engineers 1284), 15-10
IEEE 1284 Timeout, 4-5
Image, 15-10
Image color tab, 7-28, 7-39, 7-41
Image Darkness, 11-19
Image orientation, 7-43
Image Position controls, 7-43
Image Transfer tab, 7-18, 7-19
Input, 15-10
Input Hopper, 15-10
Input Hopper Card Capacity, 2-10
Interface, 2-10
interface cable, 12-4
Intermediate Transfer Media (InTM), 15-10
IPC, 7-9
ISO, 15-10
ISO 7811-2 Magnetic Stripe, 7-64
ISO encoded data format, 7-60
ISO option, 7-58, 7-59
ISO Standard Encoding Module, 7-56
ISO Track Locations, 7-64
J
JIS C 6220 Type II cards, 7-55
JIS II (Japanese Industrial Standard), 15-10
JIS II option/JIS II mode/JIS II Magnetic Head, 7-56
JIS II Standard Encoding Module, 7-56
Data Excess Error, 4-4
Job Excess Data Error, 4-7
K
K Panel, 15-10
K Panel Resin options, 7-53
K Panel Resin tab, 7-47, 7-48
L
Lam Calib Failed, 4-8
Lam Card Flip Error, 4-8
Lam Error, 4-8
Lam Heater Timeout, 4-8
Lam Lift Error, 4-8
Lam Memory Error, 4-8
Lam Pass Thru Error, 4-8
Lamination, 15-10
Lamination Arm, 8-10, 8-11
Laminator Controls, 2-27
LAN (Local Area Network), 15-10
Landscape, 15-11
LCD (Liquid Crystal Display), 15-11
LCD and Softkey Control Pad, 2-17, 2-18, 2-19, 2-20, 2-
21
LCD Display, 2-15, 2-17, 2-20, 7-62
LCD Display Messages, 4-2, 4-3, 4-4
LCD Firmware, 12-7
LCD Menu, 11-1
LCD Menu and Selecting an Option, 11-1
LCD On-Line Menu Navigation, 11-1
LED (Light Emitting Diode), 15-11
LED Light, 2-15, 2-20
less heat, 7-40
less saturated resin images, 7-40
LoCo (Low Coercivity), 15-11
Low Coercivity, 7-58
lower transfer temperature, 7-5
LPT Port (Line Printer Port), 15-11