FARGO electronics HDP600 - Page 366

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.3)
16-4
M
Mag encoding, 15-11
Mag stripe, 15-11
Mag Track, 15-11
Mag Verify, 15-11
magnetic card analyzer, 11-21
Magnetic Encoding tab, 7-54
Magnetic Stripe Encoding Modules, 7-55
Magnetic Stripe encoding process, 7-54
Magnetic Stripe verification, 7-62
Magnetic TOF, 11-21, 11-22, 11-23
Magnetic TOF setting, 11-21
Magnetic Track data, 7-65
Magnetic Track Options, 7-60
Magnetic Track Selection, 7-58, 7-59
Magnetic Track Selection option, 7-59
Magnetics encoder not installed., 4-5
Main Firmware, 12-4, 12-6
Main Firmware/LCD Firmware, 12-4
Main Print Board, 10-2
Manual Eject Each Error option, 7-62
matte-finished cards, 7-5
Maximum Accepted Card Length Range, 2-10
Maximum Accepted Card Width Range, 2-10
maximum value, 7-44
MB (Megabyte), 15-12
Measuring area positioned on card, 7-52
Media, 15-11
Memory, 15-12
Memory, 2-11
Menu, 15-12
MENU button, 11-1
Menu option, 2-18
MENU, Print Test Image and Gray/Align YMC, 11-7,
11-16
MENU, Setup Printer and Encoder Settings, 11-20
mistakenly-verified card, 7-62
Monochrome, 15-12
more heat, 7-40
Multi-Language Extension (MLE), 7-61
Multiple Card Feed Error, 4-3
multiple messages, 2-21
N
Network, 15-12
New Temperature Setting, 2-27
O
Oersted (Oe), 15-12
Off, 2-20
Offset, 15-12
Operating Temperature, 2-11
O-Ring, 15-12
OS (Operating System), 15-12
Output, 15-12
Output hopper, 15-12
Output Hopper Card Capacity, 2-11
Overlaminate, 2-28, 15-13
Overlaminate Design, 2-29
Overlaminate Options (HDP600-LC only), 2-11
Overlay, 15-12
Oversized Cards, 15-13
P
Packing the Printer, 9-12
Parallel, 15-13
Parallel Interface Port, 2-16
Parallel Port, 15-13
Pass Count, 4-19, 11-28
Pause button, 2-20
PC (Personal Computer), 15-13
PCB (Printed Circuit Board), 15-13
Peel, 15-13
Peel-Off, 15-13
Peripheral, 15-13
permanent circuit memory, 10-2
PET, 15-14
Photo, 7-30
Pinch Roller, 15-14
Pixel, 15-14
Platen, 15-14
Platen Rollers, 8-10, 8-11
Please clean your printer., 4-4
Polyester Patch Overlaminate, 2-28
PolyGuard Overlaminate, 2-28, 2-29, 15-14
Port, 15-14
Portrait, 15-14
Portrait/Landscape, 7-21
Position magnetic data, 11-21, 11-22
positive/negative image placement values, 7-44
Potentiometer, 15-14
Power Port, 2-16
Power Switch, 2-16
prevents magnetic encoding, 7-61
Print All Black With K Panel, 7-47
Print and Printers, 2-18
Print Area, 2-11
Print Back Side First option, 7-33
Print back side only, 7-34
print both sides, 7-31, 7-32
Print Both Sides option, 7-32, 7-34
Print Driver, 15-14
Print Head Lift Error, 4-9
Print Job, 15-14
Print K Only option, 7-53
Print Length, 2-7, 7-14, 7-16
Print Offset, 11-5, 11-6
Print Offset, Transfer TOF and Transfer EOF, 11-5, 11-6,
11-7, 11-15
Print Ribbon, 8-4
Print ribbon not installed., 4-10
Print Ribbon Options, 2-12
Print Ribbons, 2-22
Print Server, 15-14
Print Speed, 2-12
Print Speed-Batch Mode, 2-12
Print Station, 8-5
Print Status Screen, 2-19
Print Test Image, 4-17