FARGO electronics HDP600 - Card Lamination Module; Lamination Module Safety Messages; Opening the Card Lamination Module; Adjusting the Card Lamination Module

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDP600 High Definition Card Printer/Encoder User Guide (Rev. 2.3)
vi
Installing Printer Driver Updates ____________________________________________________ 7-10
Setting Up the Printer Driver__________________________________________________________ 7-11
Setting up Windows 2000/Windows XP ______________________________________________ 7-11
Using the Card tab (HDP600/HDP600-LC) ______________________________________________ 7-12
Using the Card tab (HDP600 CR100/HDP600-LC CR100) __________________________________ 7-13
Selecting the Card Size (HDP600 and HDP600-LC) _____________________________________ 7-14
Selecting the Custom Card Size _____________________________________________________ 7-16
Selecting the Card Type (all HDP600 Printers) _________________________________________ 7-17
Selecting the Card Hopper (HDP600 and HDP600-LC only) ______________________________ 7-19
Selecting the Card Hopper (HDP600 CR100 and HDP600-LC CR100 only) __________________ 7-20
Setting the Orientation ____________________________________________________________ 7-21
Specifying the number of Copies ____________________________________________________ 7-21
Selecting the Diagnostics button ____________________________________________________ 7-22
Selecting the Test Print button ______________________________________________________ 7-22
Selecting the About button _________________________________________________________ 7-23
Using the Device Options tab (HDP600/HDP600-LC)______________________________________ 7-24
Using the Device Options tab (HDP600 CR100/ HDP600-LC CR100) _________________________ 7-25
Adjusting the Ribbon Type_________________________________________________________ 7-26
Adjusting the Film Type___________________________________________________________ 7-27
Adjusting for the Color Matching____________________________________________________ 7-28
Adjusting for the Color Tone – Natural or Enhanced_____________________________________ 7-29
Adjusting for the Resin Dither ______________________________________________________ 7-30
Using the Print Both Sides option____________________________________________________ 7-31
Using the Split 1 Set of Ribbon Panels option __________________________________________ 7-32
Using the Print Back Side First option ________________________________________________ 7-33
Using the Print Back Side Only option________________________________________________ 7-34
Using the Rotate Front 180 Degrees or Rotate Back 180 Degrees options ____________________ 7-35
Using the Print in Single Card Mode option____________________________________________ 7-36
Using the Disable Printing option____________________________________________________ 7-37
Using the Image Color tab (HDP600)___________________________________________________ 7-38
Using the Image Transfer tab _________________________________________________________ 7-42
Adjusting the Image Position controls ________________________________________________ 7-43
Adjusting the Transfer Dwell Time and Temperature ____________________________________ 7-45
Using the K Panel Resin tab __________________________________________________________ 7-46
Selecting the Full Card with the K Panel Resin tab ______________________________________ 7-47
Selecting the Defined Area(s) with the K Panel Resin tab _________________________________ 7-48
Selecting the Undefined Area(s) with the K Panel Resin tab _______________________________ 7-49
Defining the Area to activate the Card Grid____________________________________________ 7-50
Measuring the Total Card area ______________________________________________________ 7-51
Measuring the Area to be positioned on the Card________________________________________ 7-52
Selecting the Print YMC under the K and Print K Only options ____________________________ 7-53
Using the Magnetic Encoding tab ______________________________________________________ 7-54
Using the Encoding Mode option____________________________________________________ 7-55
Encoding the Mode/Coercivity/Magnetic Track Selection_________________________________ 7-57
Reviewing the Magnetic Track Options_______________________________________________ 7-59
Reviewing the Enable MLE Support checkbox _________________________________________ 7-60
Reviewing the Verification options __________________________________________________ 7-61
Reviewing the Shift Data Left ______________________________________________________ 7-62
Reviewing the ISO Track Locations__________________________________________________ 7-63
Sending the Track Information______________________________________________________ 7-64
Reviewing the Sample String _______________________________________________________ 7-65
Reviewing the ASCII Code and Character Table________________________________________ 7-66
Using the Lamination tab (only with Card Lamination Module) ______________________________ 7-67
Selecting the Lamination Position ___________________________________________________ 7-68
Selecting the Lamination Side ______________________________________________________ 7-69
Selecting the Lamination Type______________________________________________________ 7-70