Overview table for operating a GTS iMAPLA with SunFab hydraulic motors
types of generators:
BG132 2pol. and BG160 4pol.
magnet
power in
magnet
voltage
peak generator
shaft power
recommended
typ of iMAPLA
system
type of rated maximum for
rated max.
12 17 25 25 34 34 47 47 56 12 17 25 25 34 34 47 47 56
magnet voltage 2-3 seconds
power in kW
BG132 2pol. BG160 4pol. 2pol. 2pol. 2pol. 4pol. 2pol. 4pol. 2pol. 4pol. 4pol. 2pol. 2pol. 2pol. 4pol. 2pol. 4pol. 2pol. 4pol. 4pol.
4 230 6,24 8/9/11/13 3300 - 41 58 100 70
5 230 7,80 8/9/11/13 3300 - 41 58 125 88
6 230 9,36 8/9/11/13 3300 - 41 58 86 150 106 72
7 230 10,93 8/9/11/13 3300 - 41 58 86 175 123 84
8 230 12,49 8/9/11/13 3300 2500 58 86 65 89 122 141 96 126 93 67
9 230 14,05 9/11/13/17 3300 2500 58 86 65 117 89 162 122 158 108 142 79 105 57 76
10 230 15,61 11/13/17 3300 2500 58 86 65 117 89 162 122 146 176 120 158 88 116 64 84 71
11 230 17,17 11/13/17 3300 2500 86 65 117 89 162 122 146 132 174 97 128 70 92 78
12 230 18,73 13/17/20 3300 2500 86 65 117 89 162 122 146 144 190 106 139 76 101 85
13 230 20,29 13/17/20 3300 2500 86 65 117 89 162 122 146 156 205 114 151 83 109 92
14 230 21,85 17/20/25 3300 2500 86 65 117 89 162 122 146 168 221 123 163 89 118 99
15 230 23,41 17/20/25 3300 2500 86 65 117 89 162 122 146 180 237 132 174 96 126 106
16 230 24,97 17/20/25 3300 2500 86 65 117 89 162 122 146 192 253 141 186 102 135 113
17 230 26,53 17/20/25 3300 2500 65 117 89 162 122 146 269 150 198 108 143 120
18 230 28,09 20/25/30 3300 2500 117 89 162 122 146 158 209 115 151 127
19 230 29,65 20/25/30 3300 2500 117 89 162 122 146 167 221 121 160 134
20 230 31,22 20/25/30 3300 2500 117 89 162 122 146 176 232 127 168 141
21 230 32,78 25/30 - 2500 89 122 146 244 177 148
22 230 34,34 25/30 - 2500 89 122 146 256 185 155
23 230 35,90 25/30 - 2500 89 122 146 267 193 162
24 230 37,46 25/30 - 2500 122 146 202 169
25 230 39,02 25/30 - 2500 122 146 210 176
26 230 40,58 30/35 - 2500 122 146 219 183
27 230 42,14 30/35 - 2500 122 146 227 191
28 230 43,70 30/35 - 2500 122 146 235 198
29 230 45,26 30/35 - 2500 122 146 244 205
30 230 46,82 30/35 - 2500 122 146 252 212
31 230 48,38 35 - 2500
122 146 261 219
32 230 49,
94 35 - 2500 122 146 269 226
33 230 51,51 35 - 2500 146 233
34 230 53,07 35 - 2500 146 240
35 230 54,63 35 - 2500 146 247
(frame size and num. of poles)
needed mength of oil (flow rate) in liter/minute
with a hydraulic motor displacement of ccm/rev. and type of generator
needed flow preassure (difference between input/output)
directly at the hydraulic motor in bar
with a hydraulic motor displacement of ccm/rev. and type of generator
with type of generator
rated generator speed for
hydraulic calculation in rpm
NOTE: At flow pressures upper than 200 bar, there are special high pressure components required. The pressure values are calculated with-
out any losses of pressure in the line system, tank back pressure, oil cooler unit and an optional back pressure valve. In this table only
the difference pressure of the hydraulic motor input/output terminal is listed.
Overview table for the operation of aGTS iMAPLA on SunFab hydraulic motor
generator types: BG132 2-pole and BG160 4-pole.
To Next Page
Loading...