Lenze EVS 9300 series - Page 382

Function library
Code table
9-256
l
EDSVS9332S-D12 EN 3.0
Code ImportantPossible settings
No. SelectionLenzeLCD
C0018 Switching frequency
fchop
0
0 16/8 kHz Optimum noise reduction with automatic
changeover to 8 kHz
p
1 8 kHz sine Power-optimised operation
2 16 kHz sine Noise-optimised operation
C0019 THRESH NACT=0 0 0 {1 rpm} 16000 Threshold n
act
=0
Threshold detection at n
act
=0
C0021 SLIPCOMP 0.00 0.00 {0.01 %} 20.00 Slip compensation
Only active with sensorless control below the
value of C0291
C0022 IMAX CURRENT → 0 {0.01 A} 1.50 I
N
I
max
limit current
Æ depending on C0086
Change of C0086 resets value to the assigned
default setting (1.5×Imotor)
[C0025] FEEDBACK TYPE 10
Feedback
Input of the encoder specified on the nameplate
of the Lenze motor:
C0025 automatically changes C0420, C0490,
C0495
0 COMMON C0420, C0490 or C0495 was changed
subsequently
10 RSx (Resolver) The resolver is designated with RSxxxxxxxx.
110 IT-512-5V
Incremental encoder with TTL level
111 IT-1024-5V
112 IT-2048-5V
113 IT-4096-5V
210 IS-512-5V
Sin/cos encoder
211 IS-1024-5V
212 IS-2048-5V
213 IS-4096-5V
310 AS-512-8V Stegmann single-turn sine-cosine encoder with
RS485 interface (voltage must be entered
manually)
410 AM-512-8V Multi-turn sin/cos encoder by Stegmann
company (the voltage must be entered
manually)
C0026
-199.99 {0.01 %} 199.99 FCODE (OffsetAIN)
Freely assignable code for relative analog
1 FCODE (OFFSET) 0.00
F
r
e
e
l
y
a
s
s
i
g
n
a
b
l
e
c
o
d
e
f
o
r
r
e
l
a
t
i
v
e
a
n
a
l
o
g
signals
Used for:
O
f
f
f
/
2 FCODE (OFFSET) 0.00
– Offset for terminal X6/1,2
– Offset for terminal X6/3,4
C0027
-199.99 {0.01 %} 199.99 FCODE (GAIN)
Freely assignable code for relative analog
1 FCODE (GAIN) 100.00
F
r
e
e
l
y
a
s
s
i
g
n
a
b
l
e
c
o
d
e
f
o
r
r
e
l
a
t
i
v
e
a
n
a
l
o
g
signals
Used for:
G
/
2 FCODE (GAIN) 100.00
– Gain X6/1,2
– Gain X6/3,4
C0030 DFOUT CONST 3 0
1
2
3
4
5
6
256 inc/rev
512 inc/rev
1024 inc/rev
2048 inc/rev
4096 inc/rev
8192 inc/rev
16384 inc/rev
DFOUT constant
Constant for the digital frequency output in
increments per revolution
C0032 FCODE GEARBOX 1 -32767 {1} 32767 FCODE (gearbox factor numerator)
Freely configurable code
C0033 GEARBOX DENOM 1 1 {1} 32767 Denominator of g earbox factor