Lenze EVS 9300 series - Page 397

Function library
Code table
9-271
l
EDSVS9332S-D12 EN 3.0
Code ImportantPossible settings
No. SelectionLenzeLCD
C0517 0.00 {0.01 } 1999.00
User menu
1 USER MENU 51.00 C0051/0 MCTRL-NACT
Up to 32 entries
•
U
n
d
e
r
t
h
e
s
b
c
o
d
e
s
t
h
e
n
m
b
e
r
s
o
f
t
h
e
2 USER MENU 54.00 C0054/0 Imot
• Under the subcodes the numbers of the
d
e
s
i
r
e
d
c
o
d
e
s
a
r
e
e
n
t
e
r
e
d
3 USER MENU 56.00 C0056/0 MCTRL-MSET2
d
es
i
r
e
d
co
d
es a
r
een
t
e
r
e
d
.
• Th
e
in
p
u
t
i
s
d
o
n
e
in
t
h
e
f
o
r
m
a
t
xxx.
y
y
4 USER MENU 46.00 C0046/0 N
•
T
h
e
i
n
p
u
t
i
s
d
o
n
e
i
n
t
h
e
f
o
r
m
a
t
x
x
x
.
y
y
– xxx: Code number
5 USER MENU 49.00 C0049/0 NADD
x
x
x
:
C
o
d
e
n
u
m
b
e
r
– yy: Subcode number
6 USER MENU 183.00 C0183/0 Diagnostics
y
y
• It is not checked whether the entered code
e
x
i
s
t
s
7 USER MENU 168.01 C0168/1 Fail no. act
exis
t
s.
8 USER MENU 86.00 C0086/0 Mot type
9 USER MENU 22.00 C0022/0 Imax current
10 USER MENU 5.00 C0005/0 Signal cfg
11 USER MENU 11.00 C0011/0 Nmax
12 USER MENU 12.00 C0012/0 Tir
13 USER MENU 13.00 C0013/0 Tif
14 USER MENU 105.00 C0105/0 QSP Tif
15 USER MENU 39.01 C0039/1 JOG setpoint
16 USER MENU 70.00 C0070/0 Vp speed CTRL
17 USER MENU 71.00 C0071/0 Tn speed CTRL
18 USER MENU 0 not assigned
... ... 0 not assigned
31 USER MENU 94.00 C0094/0 Password
32 USER MENU 3.00 C0003/0 Par save
[C0520] IN 1000 FIXEDPHI-0 → Selection list 4 DFSET
Input signal configuration
[C0521] VP-DIV 1000 FIXED0% →Selection list 1 DFSET
Configuration - gain factor of numerator
[C0522] RAT-DIV 1000 FIXED0% →Selection list 1 DFSET
Configuration - gearbox factor of numerator
[C0523] A-TRIM 1000 FIXED0% →Selection list 1 DFSET
Configuration - phase trimming
[C0524] N-TRIM 1000 FIXED0% →Selection list 1 DFSET
Speed trimming of DFSET
[C0525] 0-PULSE 1000 FIXED0 → Selection list 2 DFSET
Configuration - one-time zero pulse activation
[C0526] RESET 1000 FIXED0 → Selection list 2 DFSET
Configuration - integrator resetting
[C0527] SET 1000 FIXED0 → Selection list 2 DFSET
Configuration - integrator setting
C0528

-2
.
10
9
{1} 2
.
10
9
DFSET
1 0-PULSE A Phase difference between two zero pulses
2 OFFSET Offset from C0523 × C0529 + C0252
3 PULSEDISTSET  Number of increments between two set pulses
at X5/E5.
Code is available as of software version 6.2.
4 PULSEDISTACT  Number of increments between two actual
pulses at X5/E4.
Code is available as of software version 6.2.
C0529 MULTIP OFFSET 1 -20000 {1} 20000 DFSET
Offset multiplier
C0530 DF EVALUATION 0
0 with gearbox factor
DFSET
Master frequency evaluation
1 without gearbox factor
M
a
s
t
e
r
f
r
e
q
u
e
n
c
y
e
v
a
l
u
a
t
i
o
n
Evaluation of the setpoint integrator
(with/without gearbox factor)
C0531 ACT 0 DIV 1 1 {1} 16384 DFSET
Actual zero pulse divider