Lenze EVS 9300 series - Page 414

Function library
Code table
9-288
l
EDSVS9332S-D12 EN 3.0
Code ImportantPossible settings
No. SelectionLenzeLCD
C0940 NUMERATOR 1 -32767 {1} 32767 CONV1
Numerator
C0941 DENOMINATOR 1 1 {1} 32767 CONV1
Denominator
[C0942] CONV1-IN 1000 FIXED0% →Selection list 1 CONV1
Configuration - analog input
C0943 (C0942)  -199.99 {0.01 % } 199.99
C0945 NUMERATOR 1 -32767 {1} 32767 CONV2
Numerator
C0946 DENOMINATOR 1 1 {1} 32767 CONV2
Denominator
[C0947] IN 1000 FIXED0% →Selection list 1 CONV2
Configuration - analog input
C0948 (C0947)  -199.99 {0.01 % } 199.99
C0950 NUMERATOR 1 -32767 {1} 32767 CONV3
Numerator
C0951 DENOMINATOR 1 1 {1} 32767 CONV3
Denominator
[C0952] IN 1000 FIXEDPHI-0 → Selection list 4 CONV3
Configuration - analog input
C0953 (C0952)  -32767 {1 rpm} 32767
C0955 NUMERATOR 1 -32767 {1} 32767 CONV4
Numerator
C0956 DENOMINATOR 1 1 {1} 32767 CONV4
Denominator
[C0957] IN 1000 FIXEDPHI-0 → Selection list 4 CONV4
Configuration - analog input
C0958 (C0957)  -32767 {1 rpm} 32767
C0960 FUNCTION 1 1
2
3
Characteristic 1
Characteristic 2
Characteristic 3
CURVE1
Selection of the characteristic function
C0961 Y0 0.00 0.00 {0.01 %} 199.99 CURVE1
Configuration - base point
Ordinate of the p air (x = 0 % / y0)
C0962 Y1 50.00 0.00 {0.01 %} 199.99 CURVE1
Configuration - base point
Ordinate of the value pair (x1 / y1)
C0963 Y2 75.00 0.00 {0.01 %} 199.99 CURVE1
Configuration - base point
Ordinate of the value pair (x2 / y2)
C0964 Y100 100.00 0.00 {0.01 %} 199.99 CURVE1
Configuration - base point
Ordinate of the value pair (x 100 % / y100)
C0965 X1 50.00 0.01 {0.01 %} 99.99 CURVE1
Configuration - base point
Abscissa of the pair (x1 / y1)
C0966 X2 75.00 0.01 {0.01 %} 99.99 CURVE1
Configuration - base point
Abscissa of the pair (x2 / y2)
[C0967] IN 1000 FIXED0% →Selection list 1 CURVE1
Configuration - analog input
C0968 (C0967)  -199.99 {0.01 % } 199.99
[C0970] N-SET 1000 FIXED0% →Selection list 1 MFAIL
Configuration - speed input (setpoint path)
[C0971] FAUL T 1000 FIXED0 → Selection list 2 MFAIL
Configuration - digital input (activating the
mains failure control)