Lenze EVS 9300 series - Page 500

Index
abc
14-8
L
EDSVS9332S EN 3.0
Maximum speed, 9-255
Mechanical installation, 4-11
- ”Cold plate” technique, 4-16
Message, 9-219
Monitor outputs of monitoring system (MONIT),
9-157
Monitoring, 9-219
- Fault indication via digital output, 9-248
- Message, 9-219
- Of the motor temperature, 4-32
- Reactions, 9-219
- Set reactions, 9-220
- Warning, 9-219
Monitoring functions, 9-221
- Automatic adjustment H30, 9-228
- Communication error CE0, 9-224
- Contouring error P03, 9-242
- Dig-Set monitoring Sd3, 9-247
- Earth fault OC2, 9-233
- External error EER, 9-225
- Failure of a motor phase LP1, 9-229
- fault in the resolver driver H06, 9-226
- Heatsink monitoring OH (fixed), 9-235
- Heatsink monitoring OH4 (adjustable), 9-237
- Low voltage LU, 9-230
- Motor temperature monitoring OH3 (fixed), 9-236
- Motor temperature monitoring OH7 (adjustable), 9-238
- Motor temperature monitoring OH8, 9-239
- Overvoltage OU, 9-240
- Parameter error PRO, 9-244
- Parameter set error PR1, PR2, PR3, PR4, 9-245
- Phase controller overflow P13, 9-243
- Power stage identification H07, 9-227
- Resolver monitoring Sd2, 9-246
- Short-circuit OC1, 9-232
- System fault CCr, 9-223
- System speed monitoring NMax, 9-231
Motor cable
- Cable cross-sections, 4-31
- Max. permissible length, 4-31
- Screw-tightening torques, 4-31
Motor connection, 4-27
Motor phase failure detection (MLP), 9-156
motor pot, 9-263
Motor potentiometer (MPOT), 9-158
Motor protection, 4-21
Motor stator resistance, 9-258
Motor temperature, monitoring, 4-32
Motor temperature monitoring OH3 (fixed), 9-236
Motor temperature monitoring OH7 (adjustable),
9-238
Motor temperature monitoring OH8, 9-239
Mounting positions, 3-2
Multi-axis synchronisation (SYNC)
- Configuration examples, 9-215
- Correcting the phase controller, 9-214
- Cycle times, 9-211
- Fault indications, 9-214
- Operating mode, 9-209
- Phase displacement, 9-213
- Scaling, 9-215
- synchronising, 9-209
- Time slot, 9-213
Multi-axis synchronisation (SYNC1), 9-208
N
Noise emission, 3-2
Noise immunity, 3-2
Notes on operation, 6-4
O
Operating conditions, 3-2
Operating m ode of the motor control, 9-255
Operation, 6-1
Operation inhibit (DISABLE), 9-94
OR operation (OR), 9-168
Oscillations, 4-11
Oscilloscope function (OSC), 9-171
Overspeed, 2-3
Overvoltage OU, 9-240
P
Packaging, 3-2
Parameter error PRO, 9-244
Parameter set changeover (PAR), 9-96
Parameter set error PR1, P R2, PR3, PR4, 9-245
Parameter set loading, keypad EMZ9371BC, 7-6
Parameter set transfer, 2-3
- Keypad EMZ9371BC, 7-7
Parameter setting, 7-1
Parameters, P C program, 7-1
PC program, 7-1