Grove Published 02-21-2019, Control # 611-05 3-7
TMS9000-2 OPERATOR MANUAL OPERATING CONTROLS AND INDICATORS
When the top of the switch is pushed, the switch is in the high
position.
Exhaust System Cleaning Initiate Switch
This switch (6), located on the left side of the front console in
the carrier cab, is used to initiate a stationary exhaust system
cleaning. The switch must be cycled on and off to initiate
cleaning. The Exhaust System Cleaning Switch is a
maintained ON switch.
The brake and throttle pedals (and clutch pedal for cranes
with a manual transmission) must also be released. The
engine will automatically change speed as needed. The
cycle will take approximately 20 minutes.
Engine Idle Increment/Decrement Switch
The engine idle increment/decrement switch (7), located on
the left side of the front console, is used to set the engine idle
operating speed. Each push of the top of the switch (+)
increases engine idle speed by 25 rpm to a maximum of 800
rpm. Each push of the bottom of the switch (-) decreases
engine idle speed by 25 rpm to a minimum of 600 rpm. Idle
speed will revert to the factory setting two minutes after
shutting the engine down.
Remote Control On/Off Switch
The remote control on/off switch (8) is on the left side of the
console. Push the top of the switch to enable the hand-held
remote control.
Remote Control Indicator
The remote control amber indicator (9) will illuminate solid
when the remote control switch is ON and permissions for
enabling have been met. It will flash if the switch is ON but all
permissions have not been met.
ABS/ATC Switch
The Anti-lock Braking System/Automatic Traction Control
(ABS/ATC) switch (10) is on the bottom left row of the front
console. The top half of this switch is used for ABS fault code
diagnosis. The bottom deactivates the ATC for off-road
operation.
The switch is programmed for momentary operation. ATC
reverts to normal operation when the switch is cycled a
second time and whenever the system goes through a
power-up cycle. See Anti-Lock Brake System (ABS), page 4-
11 or Automatic Traction Control (ATC) Functional Overview,
page 4-12 for more information on the operation of these
switches.
Hill Start Aid (HSA) Switch (Optional)
The HSA switch (11) is located on the lower left of the
console. Push the top of the switch to de-activate the HSA
system. Refer to Hill Start Aid (HSA) (Optional-Only available
with automated transmission), page 4-31.
HSA Indicator (Optional)
The hill start aid (HSA) indicator (12) illuminates amber when
the HSA system is inactive.
Inter-Axle Lock Switch
The inter-axle differential lock switch (13) is located on the
left side of the front console. In the lock (press top of switch)
position, both rear axles are locked together and turning at
the same speed. In the unlocked (press bottom of switch)
position, the axles operate independently of each other.
Cross-Axle Lock Switch (Optional)
The cross-axle lock switch (14) is located on the left side of
the front console and is used to lock the right and left wheels
in a tandem set. The cross-axle lock increases traction on
slippery roads. It is a two position lock/unlock switch. Press
top of switch for the lock position or bottom of switch for the
unlock position.
Suspension Inflation Switch
The suspension inflation control switch (15) is located on the
left side of the console. Push the top of the switch to inflate
the suspension air bags. Push the bottom of the switch to
deflate the suspension air bags.
NOTE: The suspension air bags should be inflated at all
times except when on outriggers, or when traveling
at less than 4 km/h (2.5 mph) on job site.
NOTE: While the superstructure key switch is on, the
suspension solenoid will be energized, deflating
the air bags regardless of the carrier cab rocker
switch position.
Tire Inflation Switch
The tire inflation switch (16) is located on the left side of the
console. It is a two position switch that activates the tire
inflation system. Push the top of the switch to activate the tire
inflation system. An amber indicator will illuminate and a
warning buzzer will sound when the switch is in the ON
position.
Heater/Air Conditioner Fan Switch
The heater/air conditioner fan switch (17) is located on the
right of the console. The switch controls the speed which in
CAUTION
Do not operate the cross axle lock while crane wheels are
spinning or at speeds over approximately 16 km/h
(10 mph) as damage may occur.
To Next Page
Loading...
Need help?
General
