About User Types
3-3
1
1
3
Convenient use
5
6
Function name Set value
When no instruction
from RIP exists
*1
*1. This is the setting value to be used for printing when setting value is not specified at the RIP software (host) side, or, you give priority
to the setting value at the machine side, even if you set “Host” to the type registration of this machine.
Outline
HEATER
(P.3-8)
SET
TEMP
Pre-
Heater
OFF/ 20 ~ 50C
(OFF/ 68 ~ 122?F)
Sets heater conditions.
Print
Heater
OFF/ 20 ~ 50C
(OFF/ 68 ~ 122F)
Post
Heater
OFF/ 20 ~ 50C
(OFF/ 68 ~ 122F)
SET
TIME
STANDBY
NONE/ 0 ~ 90 min (10min unit)
OFF TIME NONE/ 0 ~ 90 min (10min unit)
PRINT
MODE
( P.3-12)
PASS HOST / STD / FAST / FINE
STD
Sets a print quality level and
printing direction.
SCAN DPEED HOST
/ STD / FAST
FAST
SCAN DIRECTION HOST / Bi-D / Uni-D
Uni-D
LOGICAL SEEK HOST / ON / OFF
ON
INK LAYERS ( P.3-26) HOST /1 ~ 9
1
Sets the number of layers in
which ink is to be applied.
DRYING
TIME
( P.3-12)
SCAN HOST /0.0 ~ 19.9 sec
0 sec
Sets the time to wait for ink
drying.
Draw. END HOST /0 ~ 999 sec
0 sec
AUTO CUT ( P.3-26) HOST /ON / OFF
OFF
Cuts the media automatically
after printing.
PRE-FEED ( P.3-26) HOST
/ON / OFF
OFF
Feeds the media back and forth
before printing.
When sticky media is used,
select ON.
MARGIN
( P.3-17)
LEFT HOST / -20 ~ 75mm (1mm unit)
0 mm
Sets a non-printing area along
the right and left edges of the
media.
RIGHT HOST
/ -20 ~ 75mm (1mm unit)
0 mm
COLOR
PATTERN
(P.3-18)
LEFT
HOST
/ ON / OFF
OFF
Prints the color pattern on the
media right edge (when Sb52 is
filled, on the both edges).
RIGHT
HOST
/
ONx1 ~ ONx5 / OFF
(When Sb52 is filled)
REFRESH ( P.3-26)
HOST
/ Level 0
(Refresh interval
long)
~ 3
(Refresh interval short)
Level 3
Refreshes the print heads during
printing.
VACUUM ( P.3-26)
HOST
/ STANDARD / WEAK /
Little WEAK / STRONG / OFF
STANDARD
Sets the absorbability of the
media.
FeedSPEED LEVEL ( P.3-26)
*2
*2. When “ON” is set to “Select device” in “Setting of feeding and take up” of the machine setting, the feeding speed is limited on
max.150%.
HOST / 10 ~ 200%
10%............. 6mm/sec
100%........... 60mm/sec
200%......... 120mm/sec
100
Changes the media feeding
speed in printing.
AUTO
CLEANING
( P.3-20)
ON
INTERVAL
10 ~ 1000 ~ 10000 mm
Sets the auto cleaning of the print
head every completion of
printing.
TYPE NORMAL
/ SOFT / HARD
OFF
Print.
CLEANING
( P.3-22)
CLEAN
ING
ON
INTERVAL
10 ~ 1000 ~ 10000 mm
Sets the auto cleaning of the print
head in printing.
TYPE
NORMAL / SOFT / HARD
OFF
WIPING
SCAN COUNT 0 ~ 9990
Sets the wiping operation during
printing.
TEMP.
difference
0 ~ 60
MEDIA
DETECT
( P.3-25)
DETECT METHOD SELECT / WIDTH
Sets the method for detecting the
media.
CUTTING DETECT
NONE / BOTH EDGE
/
LEFT EDGE / RIGHT EDGE
FEED ORIGIN ( P.3-26) ON / OFF
Setting the media feeding
direction to LED pointer when
changing the printing origin
position.
To Next Page
Loading...
