A - 9
3.4.2 A/D conversion enable/disable setting (Un\G0).................................................................... 3 - 55
3.4.3 CH[ ] average time/average number of times/moving average/time constant settings
(Un\G1 to Un\G8) ................................................................................................................. 3 - 56
3.4.4 A/D conversion completed flag (Un\G10) ............................................................................. 3 - 57
3.4.5 CH[ ] digital output value (Un\G11 to Un\G18) ..................................................................... 3 - 58
3.4.6 Write data error code (Un\G19) ............................................................................................ 3 - 59
3.4.7 Setting range (Un\G20, Un\G21) .......................................................................................... 3 - 59
3.4.8 Offset/gain setting mode offset/gain specification (Un\G22, Un\G23) .................................. 3 - 60
3.4.9 Averaging process specification (Un\G24, Un\G25))............................................................ 3 - 61
3.4.10 CH[ ] maximum value/minimum value storage area (Un\G30 to Un\G45)............................ 3 - 62
3.4.11 Input signal error detection extended/input signal error detection setting (Un\G47) ............ 3 - 62
3.4.12 Warning output settings (Un\G48) ........................................................................................ 3 - 64
3.4.13 Input signal error detection flag (Un\G49) ............................................................................ 3 - 65
3.4.14 Warning output flag (Un\G50,Un\51) .................................................................................... 3 - 66
3.4.15 Scaling enable/disable setting (Un\G53) .............................................................................. 3 - 66
3.4.16 CH[ ] scaling value storage area (Un\G54 to Un\G61) ......................................................... 3 - 67
3.4.17 CH[ ] scaling upper / lower limit value (Un\G62 to Un\G77) ................................................. 3 - 67
3.4.18 CH[ ] conversion starting time setting (for 2-wire transmitter) (Un\G78 to Un\G83)
(Q66AD-DG only) .................................................................................................................3 - 67
3.4.19 CH[ ] process alarm upper/lower limit value (Un\G86 to Un\G117)...................................... 3 - 68
3.4.20 CH[ ] rate alarm warning detection period (Un\G118 to Un\G125)....................................... 3 - 69
3.4.21 CH[ ] rate alarm upper/lower limit value (Un\G126 to Un\G141) .......................................... 3 - 70
3.4.22 CH[ ] input signal error detection setting value/CH[ ] Input signal error detection lower
limit setting value (Un\G142 to Un\G149)
CH[ ] Input signal error detection upper limit setting value (Un\G150 to Un\G157).............. 3 - 71
3.4.23 Mode switching setting (Un\G158, Un\G159) ....................................................................... 3 - 74
3.4.24 Save data classification setting (Un\G200) (Q68AD-G only)................................................ 3 - 74
3.4.25 Factory default and User range settings offset/gain value (Un\G202 to Un\G233) .............. 3 - 75
4 SETUP AND PROCEDURES BEFORE OPERATION 4 - 1 to 4 - 24
4.1 Handling Precautions....................................................................................................................... 4 - 1
4.1.1 Attaching a module fixing bracket (Q66AD-DG only) ............................................................. 4 - 2
4.2 Setup and Procedures before Operation ......................................................................................... 4 - 3
4.3 Part Names...................................................................................................................................... 4 - 4
4.4 Wiring............................................................................................................................................... 4 - 7
4.4.1 Wiring precautions.................................................................................................................. 4 - 7
4.4.2 External wiring ........................................................................................................................ 4 - 8
4.4.3 Connector/terminal block converter module ......................................................................... 4 - 11
4.5 Intelligent Function Module Switch Setting .................................................................................... 4 - 12
4.6 Offset/Gain Settings....................................................................................................................... 4 - 14
4.6.1 Offset/gain settings (Q68AD-G)............................................................................................ 4 - 15
4.6.2 Offset/gain settings (Q66AD-DG) ......................................................................................... 4 - 19
4.6.3 A/D conversion value storage during offset/gain setting ...................................................... 4 - 24
5 UTILITY PACKAGE (GX Configurator-AD) 5 - 1 to 5 - 33
5.1 Utility Package Functions ................................................................................................................ 5 - 1
5.2 Installing and Uninstalling the Utility Package ................................................................................. 5 - 2
To Next Page
Loading...
Need help?
General
