Oki C911 - Page 148

45530603TH Rev.2
5-7
Oki Data CONFIDENTIAL
5. MAINTENANCE MENUS
Item Settings Functions
Print
Adjust
Tray1 Duplex X
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 1,
During the front-side printing of duplex
printing (when feeding from the duplex
unit), adjusts the location of a whole
printing image (in 0.25-millimeter
increments) perpendicular to the direction
of paper movement (i.e. horizontally).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Duplex unit should be installed.
Duplex Y
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 1,
During the front-side printing of duplex
printing (when feeding from the duplex
unit), adjusts the location of a whole
printing image (in 0.25-millimeter
increments) parallel to the direction of
paper movement (i.e. vertically).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Duplex unit should be installed.
Overprint X
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 1,
During the second printing of spot-color
over printing (when feeding from the
duplex unit), adjusts the location of a
whole printing image (in 0.25-millimeter
increments) perpendicular to the direction
of paper movement (i.e. horizontally).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- C941 and Duplex unit should be installed.
Overprint Y
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 1,
During the second printing of spot-color
over printing (when feeding from the
duplex unit), adjusts the location of a
whole printing image (in 0.25-millimeter
increments) parallel to the direction of
paper movement (i.e. vertically).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- C941 and Duplex unit should be installed.
Item Settings Functions
Print
Adjust
Tray2 X Adjust 0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 2,
Adjusts the position of a whole printing
image (in 0.25-millimeter increments)
perpendicular to the direction of paper
movement (i.e. horizontally).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Tray 2 should be installed.
Y Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 2,
Adjusts the position of a whole printing
image (in 0.25-millimeter increments)
parallel to the direction of paper
movement (i.e. vertically).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Tray 2 should be installed.
Duplex X
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 2,
During the front-side printing of duplex
printing (when feeding from the duplex
unit), adjusts the location of a whole
printing image (in 0.25-millimeter
increments) perpendicular to the
direction of paper movement (i.e.
horizontally).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Tray 2 and Duplex unit should be
installed.
Duplex Y
Adjust
0.00 millimeter
+0.25
millimeter to
+2.00
millimeter
-2.00 millimeter
to
-0.25 millimeter
To the paper fed from Tray 2,
During the front-side printing of duplex
printing (when feeding from the duplex
unit), adjusts the location of a whole
printing image (in 0.25-millimeter
increments) parallel to the direction of
paper movement (i.e. vertically).
Print image exceeding the printable
area is clipped by this specification.
[Display Conditions]
- Tray 2 and Duplex unit should be
installed.