45530603TH Rev.2
5-33
Oki Data CONFIDENTIAL
5. MAINTENANCE MENUS
③
Pressing the CANCEL button during the test cancels the test (turning on the
ONLINE lamp), restoring the state of step 2.
<REG ADJ RESULT is performed>
Same button operation as of REG ADJ EXECUTE in (2)
<WRT POS ADJ EXE is performed>
①
Write start position adjustment is executed and the lower line of the display
starts blinking.
②
When the test ends, the upper line of the display shows the result of the test (OK
or an error name), the lower display shows ‘****RESULT’.
oK
WRt Pos aDJ RsLt
Pressing the MENU button displays the next test result.
Pressing the MENU
button displays the preceding test result.
Press the BACK button to return to step 2 (WRT POS ADJ RSLT).
Remark: The following message appears while the device is initialized or
issues an alarm or when the cover is open.
ng
WRt Pos aDJ RsLt
③
Pressing the CANCEL button during the test cancels the test (turning on the
ONLINE lamp), restoring the state of step 2.
<WRT POS ADJ RSLT is performed>
Same button operation as of WRT POS ADJ EXE in (2)
4. Repeat steps 2 and 3 when necessary.
5. Press the BACK button to end the test (the state is restored to the step 1).
Color registration correction test items
Display Detail
REG ADJ EXECUTE Executes color
registration adjustment.
OK: Stores the adjustment value to EEPROM.
NG: Displays an error and updates
RESULT only.
REG ADJ RESULT Displays the result of
'REG ADJ EXECUTE'.
For displayed items, refer to “REG ADJUST
RESULT display item”.
WRT POS ADJ EXE Executes the adjustment
of the writing starting
position.
OK: Stores the adjustment value to EEPROM.
NG: Displays an error and updates
RESULT only.
WRT POS ADJ RSLT Displays the result of
'WRT POS ADJ EXE'.
For displayed items, refer to “WRT POS
ADJ RSLT display item”.
Panel display at the completion of color registration correction test
Upper line of the display
Lower line of the display Detail
OK / ERROR
NAME
REG ADJ RESULT/
WRT POS ADJ
RSLT
Displays only “OK” in the upper line of the
display when no error occurs.
Displays an error name when an error occurs.
Displays “**** RESULT” corresponding to the
test executed in the lower line of the display
Color registration correction test errors
Displayed error name Contents
SECTION OVER Non-detection error of pattern edge in the write start position correction
Zsens OVER Detects an abnormal correction value in the write start position correction.
S1-SR RANGE(R) Detects an abnormal color-registration correction value in the right
position of S1 vertical-scanning coarse adjustment
S1-SR RANGE(L) Detects an abnormal color-registration correction value in the left
position of S1 vertical-scanning coarse adjustment
S2-SR RANGE(R) Detects an abnormal color-registration correction value in the right
position of S2 vertical-scanning coarse adjustment
S2-SR RANGE(L) Detects an abnormal color-registration correction value in the left
position of S2 vertical-scanning coarse adjustment
S3-SR RANGE(R) Detects an abnormal color-registration correction value in the right
position of S3 vertical-scanning coarse adjustment
S3-SR RANGE(L) Detects an abnormal color-registration correction value in the left
position of S3 vertical-scanning coarse adjustment
S4-SR RANGE(R) Detects an abnormal color-registration correction value in the right
position of S4 vertical-scanning coarse adjustment
S4-SR RANGE(L) Detects an abnormal color-registration correction value in the left
position of S4 vertical-scanning coarse adjustment
To Next Page
Loading...
