Need help?Do you have a question about the Peri Trio and is the answer not in the manual?
General| Brand | Peri |
|---|---|
| Model | Trio |
| Category | Construction Equipment |
| Language | English |
Overview of the primary components of the TRIO panel formwork system.
Explanation of pictograms and conventions used in the instructions.
Information regarding the illustrative nature of the system representation.
Identifies the intended users and their responsibilities for the formwork system.
List of supplementary documents and resources for PERI products.
General safety instructions applicable across different formwork systems.
Safety instructions specific to the TRIO system's operational requirements.
Guidelines for the safe storage and transportation of TRIO panels and components.
Instructions for using the MAXIMO stacking device for panels.
Details on using the TRIO Corner stacking aid for panels.
Procedure for the initial assembly of the main formwork structure.
Instructions for installing the closing section of the formwork.
Process of pouring concrete using the formwork system.
Procedure for striking the formwork and moving panels.
Visual guide to available panel sizes, widths, and types.
Details on using the Alignment Coupler BFD for panel connections.
Use of TAR 85 Waler for bracing and load transfer in panel connections.
Application of Waler 85 for stopend formwork.
Details on the standard DW 15 tie system and its load capacity.
Details on the DW 20 tie system for higher concrete pressures.
Method for inclined anchoring using the DW 15 tie system.
Component for attaching push-pull props to formwork panels.
Base plate for push-pull props and kickers.
Forming continuous right-angled corners with wall thicknesses up to 40 cm.
Using Articulated Corner TGE for angles of 75° and more.
Forming 90° T-junctions with wall thicknesses up to 60 cm.
Forming obtuse-angle connections using various TRIO panels.
Techniques for creating wall offsets up to 100 cm.
Adjusting panel connections for height differences.
Using contractor-supplied timber for length compensation.
Using TRIO Filler Plate LA for compensations from 6 to 36 cm.
Using TRIO Filler Profile TPP for compensations from 20 to 36 cm.
Using the Stopend Panel TR 24 for 24 cm wall thickness.
Transferring concrete pressure using timbers and plywood.
Assembly of stopend panels without a water bar.
Assembly of stopend panels with a water bar.
Assembly of stopend panels with an expandable water bar.
Using Stopend Waler with a height of 270 mm.
Using Stopend Waler with a height of 330 mm.
Details and assembly of the TRIO 120 x 270 concreting platform.
Procedure for attaching the concreting platform to the panel.
How to position the guardrail in an inclined angle before moving.
Details and assembly of the MX 100 x 240 concreting platform.
Steps for preparing the MX 100 x 240 concreting platform for installation.
Mounting end guardrail frames and extensions.
How to attach the MX 100 x 240 platform using lifting gear.
Procedure for mounting the MX 100 x 240 platform onto the formwork panel.
Details and assembly of the concreting platform with hatch.
Steps for preparing the platform with hatch before installation.
Instructions for mounting the ladder onto the formwork.
Installing the platform with hatch at internal corners.
Using the MAXIMO MXK bracket system for platforms.
Details of the MXK-RS bracket for connecting push-pull props.
Using TRG 80 and TRG 120 brackets for platforms.
Component for mounting guardrails to TRIO panels.
Instructions for extending formwork up to a height of 5.40 meters.
Instructions for extending formwork up to a height of 8.10 meters.
Using tension and compression braces for wall thicknesses up to 100 cm.
Component for anchoring foundations when tie positions are missing.
Using Foundation Straps for forming individual foundations.
Forming circular structures using polygonal panel arrangements.
Details and assembly of the TSE shaft element.
Description of the formwork in its shuttered state.
Procedure for striking the shaft formwork.
Adding extensions to shaft formwork elements.
Configuration for shaft formwork using two corners.
Configuration for shaft formwork using four corners.
Illustrations showing wall thicknesses for shaft formwork.
Panel connection method for standard joints with TRIO 330.
Combining TRIO 330 and 270 panels for height.
Panel connection method for external corners with TRIO 330.
Forming obtuse and acute-angled corners with TRIO 330.
Extending TRIO 330 formwork with 270 height section.
Details on extending TRIO 330 formwork up to 5.40 meters.
Details on extending TRIO 330 formwork up to 6.00 meters.
Details on extending TRIO 330 formwork up to 8.10 meters.
Overview of TRIO Aluminium panels, specifications, and combination rules.
Details on TRIO Structure panels for special concrete surfaces.
Components required for forming 90° corners with TRIO Structure.
Components required for forming 135° corners with TRIO Structure.
To Next Page
