EasyManuals Logo

Siemens SINUMERIK 840C Installation Instructions

Siemens SINUMERIK 840C
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #1051 background imageLoading...
Page #1051 background image
12 Functional Descriptions 10.94
12.27.2 Parameter set switchover with SW 4 and higher (option)
"
Ratio" parameter group
The "Ratio (R)" parameter group contains the following parameters:
Axis
1stPaSe
2ndPaSe 3rdPaSe
4thPaSe 5thPaSe 6thPaSe 7thPaSe 8thPaSe
Parameter
Number of teeth, motor 3032* 3036* 3040* 3044* 3048* 3052* 3056* 3060*
Number of teeth, spindle 3064* 3068* 3072* 3076* 3080* 3084* 3088* 3092*
Zero
mark compensation + 3096* 3100* 3104* 3108* 3112* 3116* 3120* 3124*
Zero mark compensation - 3128* 3132* 3136* 3140* 3144* 3148* 3152* 3156*
Backlash compensation 220* 3160* 3164* 3168* 3172* 3176* 3180* 3184*
MD
This parameter set acts only on the first measuring system (mounting on motor side), i.e. a
variable gear ratio may be required. The second measuring system in normally a direct
measuring system (mounting on load side). Between this measuring system and the
movements to be measured, there is normally a fixed gear ratio which can be taken into
account, as with previous software versions, by means of pulse/path evaluation.
Spindle
1stPaSe
2ndPaSe 3rdPaSe
4thPaSe 5thPaSe 6thPaSe 7thPaSe 8thPaSe
Parameter
Number of teeth, motor 2400* 2401* 2402* 2403* 2404* 2405* 2406* 2407*
Number of teeth, spindle 2408* 2409* 2410* 2411* 2412* 2413* 2414* 2415*
Zero
mark compensation + 2416* 2417* 2418* 2419* 2430* 2431* 2432* 2433*
Zero mark compensation - 2434* 2435* 2436* 2437* 2438* 2439* 2440* 2441*
MD
If the function "Extended parameter set switchover" is not active, then the following value
settings are fixed, i.e. the values given above are irrelevant:
Axis: 3032* ... 3060* = 1 (Number of teeth, motor)
3064* ... 3092* = 1 (Number of teeth, spindle)
3096* ... 3124* = 0 (Zero mark compensation +)
3128* ... 3156* = 0 (Zero mark compensation -)
3160* ... 3184* = MD 220* (backlash compensation)
The backlash compensation value of the 1st parameter set is
activated in all parameter sets.
Spindle: 2400* ... 2407* = 1 (Number of teeth, motor)
2408* ... 2415* = 1 (Number of teeth, spindle)
2416* ... 2433* = 0 (Zero mark compensation +)
2434* ... 2441* = 0 (Zero mark compensation -)
12–276
© Siemens AG 1992 All Rights Reserved 6FC5197- AA50
SINUMERIK 840C (IA)

Table of Contents

Other manuals for Siemens SINUMERIK 840C

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840C and is the answer not in the manual?

Siemens SINUMERIK 840C Specifications

General IconGeneral
BrandSiemens
ModelSINUMERIK 840C
CategoryControl Unit
LanguageEnglish

Related product manuals