6 NC Machine Data (NC MD), NC Setting Data (NC SD) 03.95
6.2 General machine data (general data)
6.2 General machine data (general data)
Velocity behind pre-limit switch
1
Default value Lower input limit Upper input limit Units
500 +0 100 000
1 000 units/
min (IS)
Active on
NC Stop
Velocity diagram on crossing the software limit switch with circular interpolation
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Axis stop point
a
a
a
a
a
a
a
a
a
a
a
a
s (mm)
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
V (m/min)
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Position of SW limit switch
NC MD 2240-2371
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Position of SW pre-limit switch
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NC MD 1100*
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Braking characteristic
Velocity behind SW pre-limit switch
Note:
NC MD 1 has no effect when 0 is entered in NC MD 1100*.
See also NC MD 2240-2371, NC MD 1100* and NC MD 5003.7.
6–6 ©
Siemens AG 1992 All Rights Reserved 6FC5197- AA50
SINUMERIK 840C (IA)
To Next Page
Loading...
Need help?
General
