6 NC Machine Data (NC MD), NC Setting Data (NC SD) 12.93
6.6.5 Leadscrew error compensation bits (compensation flags)
6.6.5 Leadscrew error compensation bits (compensation flags)
0
MD
No.
7 6 5 4 3 2 1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Bit No.
yes/no +/–
6000 C point 4
yes/no +/–
C point 3
yes/no +/–
C point 2
yes/no +/–
C point 1
yes/no +/–
6001 C point 8
yes/no +/–
C point 7
yes/no +/–
C point 6
yes/no +/–
C point 5
yes/no +/–
6002 C point 12
yes/no +/–
C point 10
yes/no +/–
C point 9
yes/no +/–
C point 11
-//-
-//-
-//-
-//-
-//-
-//-
-//-
-//-
-//-
-//-
-//-
yes/no +/–
6248 C point 996
yes/no +/–
C point 995
yes/no +/–
C point 994
yes/no +/–
C point 993
yes/no +/–
6249 C point 1000
yes/no +/–
C point 999
yes/no +/–
C point 998
yes/no +/–
C point 997
- Bit = 0 Negative compensation
+ Bit = 1 Positive compensation
no Bit = 0 No compensation
yes Bit = 1 No compensation
All MD for leadscrew error compensation become effective on Power On and following
completion of reference point approach. See Section entitled ”Functional Descriptions”.
Default value: All 0
6–154 © Siemens AG 1992 All Rights Reserved 6FC5197- AA50
SINUMERIK 840C (IA)
To Next Page
Loading...
