Siemens SINUMERIK 840C - Page 442

10.94 7 Drive Machine Data (SIMODRIVE Drive MD)
7.1.2 MSD MD (data description - SW 3)
Reduction factor reset time motor 1
202
Default value Lower input limit Upper input limit Units
100 1 200 %
Active
at once
Input of reset time reduction factor for the upper adaptation speed. This machine data contains
the multiplication factor for the reset time characteristic (see diagram MD 203).
Selection adaption speed controller motor 1
203
Default value Lower input limit Upper input limit Units
0 0 7 –
Active
at once
Input of activation point for speed controller adaption. The diagram shows how the individual
machine data influence the speed characteristic.
a a a
a
a
a
a
a
a
a a a
n
a a a a a a a a a
a
a a a a a a a
a
a
a a a a a a a
a
a
a a a a a a a
a
a a a a a a a a a
K
P
, T
N
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 199/MD 286
a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a
n
1
(MD 195/MD 283)
Lower speed
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 202/MD 289
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 201/MD 288
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 198/MD 285
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 31/MD 265
a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a
n
2
(MD 196/MD 284)
Upper speed
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
MD 32/MD 266
0: No speed controller adaption
1: No function assigned at present
2: Speed controller adaption activated
3: No function assigned at present
Note:
The speed controller adaption function is available only for operation in gear stage 1.
©
Siemens AG 1992 All Rights Reserved 6FC5197- AA50 7–27
SINUMERIK 840C (IA)