Siemens SINUMERIK 840C Installation Instructions

7 Drive Machine Data (SIMODRIVE Drive MD) 04.96
7.2.2 FDD MD (data description - SW 3)
Graphic representation:
Adaptation of speed controller machine data by means of characteristic
a a a
a
a
a
a
a
a
a a a
n
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
MD 1411
a a a a a a a a a a
a
a a a a a a a a
a
a
a a a a a a a a
a
a a a a a a a a a a
K
P
, T
N
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
MD 1412
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
MD 1401
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
MD 1409
a a a a a a a a a a a a a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a a a a a a a a a a a a a
MD 1408
a a a a a a a a a a a a a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a
a a a a a a a a a a a
a
a a a a a a a a a a a a a
MD 1410
a a a a a a a a a a a a
a
a a a a a a a a a a
a
a
a a a a a a a a a a
a
a a a a a a a a a a a a
MD 1407
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
Lower speed
range with
constant P gain/
integral-action
time
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
Upper speed
range with
constant P gain/
integral-action
time
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
Adaptation
range
Upper adaptation speed
1412
Default value Lower input limit Upper input limit Units
0 0 7 200 rev/min
Active
at once
Input of upper speed threshold for adaptation of the speed controller machine data. When the
adaptation function is active, the control machine data MD 1408 and MD 1410 are applied at
speeds n > MD 1412. In the medium range MD 1411 < n < MD 1412, linear interpolation
takes place between the two control machine data sets.
See machine data "Adaptation lower speed threshold" (MD 1411) for diagram.
Selection adaption speed controller
1413
Default value Lower input limit Upper input limit Units
0 0 1 –
Active
at once
This machine data allows adaptation of the speed controller machine data to be controlled as a
function of speed.
Input 0: The adaptation function is not active. The settings in control machine data
MD 1407 and MD 1409 are applicable over the entire speed range. Control
machine data MD 1408 and MD 1410 are not taken into account.
Input 1: The adaptation function is active. See machine data MD 1411 and MD 1412 for
description.
7–66 ©
Siemens AG 1992 All Rights Reserved 6FC5197- AA50
SINUMERIK 840C (IA)

Siemens SINUMERIK 840C Specifications

General

Brand	Siemens
Model	SINUMERIK 840C
Category	Control Unit
Language	English