EasyManuals Logo

Siemens SINUMERIK 840C Installation Instructions

Siemens SINUMERIK 840C
1154 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #826 background imageLoading...
Page #826 background image
10.94 12 Functional Descriptions
12.7.2 Description of the spindle modes
In main spindle drives, the torque is limited as follows (cf. Fig. 1):
• Constant torque up to rated speed n
n
: Torque = const
• Constant power above rated speed
up to breakdown speed n
k
: Torque 1 / n
• Power reduction at higher speeds up to n
max
: Torque 1 / (n*n)
Allowance is made for these characteristics in the control in the form of an acceleration
adaptation which is simple to parameterize:
• Constant acceleration (according to MD 478* as with previous SW) up to a freely settable
speed limit n
x
.
The speed limit nx is entered via a new MD 2471* - MD 2478* which parameter-set-
specific.
• Above speed limit nx, the acceleration rate is reduced according to the equation:
Acceleration= MD 478* n
x
/ n
n: Present speed
It may to be necessary to make allowance for the acceleration characteristic of the induction
drive which drops in proportion to 1/(n*n) above the speed range of constant power. This can
be achieved approximately by means of an additionally applied adaptation factor c (MD 2479* -
MD 2486*):
Acceleration= (MD 478*) for n n
x
Acceleration= (MD 478*) * [n
x
/ (n * c)+(c - 1) / c] for n>n
x
Fig. 3 Possible shapes of acceleration characteristic when adaptation factor is varied. For c = 1 (1 = 100 %),
the acceleration above speed limit nx is reduced in inverse proportion to the speed.
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Acceleration
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
MD 478*
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
c = 1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
c < 1
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
c > 1
a
a
a
a
a
a
a
a
a
a
a
a
0
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Speed n
a
a
a
a
a
a
a
a
a
a
a
a
n
x
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
n
max
© Siemens AG 1992 All Rights Reserved 6FC5197- AA50
12–51
SINUMERIK 840C (IA)

Table of Contents

Other manuals for Siemens SINUMERIK 840C

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840C and is the answer not in the manual?

Siemens SINUMERIK 840C Specifications

General IconGeneral
BrandSiemens
ModelSINUMERIK 840C
CategoryControl Unit
LanguageEnglish

Related product manuals