Need help?Do you have a question about the SimCom SIM5350 and is the answer not in the manual?
General| Brand | SimCom |
|---|---|
| Model | SIM5350 |
| Category | Control Unit |
| Language | English |
Defines the document's purpose and coverage.
Lists standards and documents referenced in the manual.
Provides definitions for key terms and abbreviations used.
Details the RS-232 interface settings and default values.
Explains the structure and rules for forming AT commands.
Describes how the module responds to commands and error reporting.
Command to answer an incoming voice or data call.
Command used for dialing numbers and controlling supplementary services.
Controls whether characters are echoed back to the TE.
Command to disconnect an active voice, CSD, or data call.
Requests product info like manufacturer, model, IMEI, and capabilities.
Sets the volume level for the monitor speaker.
Resumes data mode after exiting command mode.
Selects pulse dialing (setting is ignored).
Controls automatic answering based on the number of rings.
Sets the character used to terminate command lines.
Sets the character used for response formatting.
Sets the character for command line editing (backspace).
Pause before blind dialing (command is ignored).
Sets the connection completion timeout.
Sets pause time for comma in dial strings.
Sets delay before disconnecting after no received signal.
Selects tone dialing (not supported).
Determines content of headers/trailers in responses.
Determines if unsolicited result codes are transmitted.
Restores user settings to factory defaults.
Sets all parameters to manufacturer defined profile.
Requests manufacturer identification text.
Requests model identification text.
Requests firmware revision identification.
Sets the serial interface baud rate temporarily.
Sets the module's flow control.
Requests a list of additional capabilities.
Selects the type of number for dialing commands.
Cancels voice calls.
Controls presentation of intermediate result codes.
Returns a list of current calls of the ME.
Provides an extended report of call setup or in-call failures.
Controls extended format of incoming call/GPRS request indications.
Selects whether ATH or DTR disconnects a voice connection.
Transmits DTMF tones and arbitrary tones during a voice call.
Enables/disables presentation of CLI to the called party.
Allows calling subscriber to enable/disable CLI presentation.
Enables/disables presentation of COL to the calling subscriber.
Controls call forwarding supplementary service.
Controls Call Waiting supplementary service.
Controls call related services like hold, conference, transfer.
Controls presentation of unsolicited result codes for network registration.
Selects and registers the GSM/UMTS network operator.
Locks, unlocks, or interrogates a ME or network facility.
Sets a new password for facility lock functions.
Enables subscriber to get call cost information.
Enables/disables presentation of notification result codes.
Returns a list of operator names from the ME.
Sets the preferred band for the MS.
Reports mobile equipment error codes.
Selects the level of functionality in the ME.
Sends password (PIN, PUK) to the ME.
Returns received signal strength and bit error rate.
Enables/disables reporting of CME ERROR codes.
Manages the module's Real Time Clock.
Provides limited access to the SIM database.
Resets the accumulated call meter value.
Sets the maximum accumulated call meter value.
Enables/disables time zone change event reporting.
Requests manufacturer identification text.
Requests model identification text.
Requests firmware revision identification.
Requests product serial number identification.
Informs TA about the character set used by TE.
Returns subscriber MSISDNs.
Returns IMSI to identify the SIM card.
Reads the ICCID of the SIM card.
Validates PUK and defines a new PIN code.
Validates PIN2, PUK2, and defines a new PIN2 code.
Queries remaining valid tries for PINs and PUKs.
Enables/disables +EIND unsolicited result code.
Enables +ECSQ unsolicited result code for signal level.
Requests network to enter Fast Dormancy mode for power saving.
Selects operator with specified ARFCN.
Sets or cancels cell lock, and retrieves locked cells.
Indicates errors related to mobile equipment or network.
Selects the messaging service (GSM phase 2/2+).
Selects memory storages for reading/writing SMS.
Specifies input/output format for short messages (PDU/Text).
Updates the SMSC address for outgoing SMS.
Sets additional parameters for text mode SMS.
Controls whether detailed header info is shown in text mode.
Selects accepted message types for cell broadcast.
Selects how new messages are indicated to the TE.
Returns messages with status from storage.
Returns message with location value from storage.
Confirms successful receipt of a new message.
Sends a message from TE to the network.
Sends message with location from preferred storage.
Stores message to memory storage.
Deletes message from preferred message storage.
Specifies PDP context parameter values.
Specifies QoS Profile for Activate PDP Context Request.
Specifies minimum acceptable profile for PDP context.
Attaches or detaches MT from Packet Domain service.
Activates or deactivates the specified PDP context.
Returns a list of PDP addresses for specified contexts.
Enables/disables automatic response to PDP context activation request.
Manually responds to a network request for PDP context activation.
Enables/disables sending of GPRS event unsolicited result codes.
Controls presentation of unsolicited result codes for GPRS registration.
Specifies service or preference for sending MO SMS.
Specifies 3G Quality of Service Profile.
Sets the output voltage for the LDO.
Configures output frequency and duty for PWM pin.
Selects a clock as the source clock for the PWM pin.
Sets GPIO to input or output state.
Sets the value of specified GPIO to high or low.
Gets the value (high or low) of a specified GPIO.
Sets GPIO pin as interrupt source with detect/polarity types.
Enables/disables function for special GPIO.
Writes values to a register of an IIC device.
Reads values from a register of an IIC device.
Configures if RI pin is pulled down when URC is reported.
Resets RI pin of serial port.
Configures UART or USB as AT port.
Selects PCM audio path between USB Audio and external codec.
Selects codec chip for audio.
Lists verbose and numeric result codes.
Lists response strings for AT+CEER command.
To Next Page
