WAGO I/O-SYSTEM 750 User Manual

454 List of Figures WAGO-I/O-SYSTEM 750
750-8208 PFC200 CS 2ETH RS CAN DPM
Manual
Version 1.1.0, valid from FW Version 02.06.20(09)
List of Figures
Figure 1: View of device ....................................................................................... 27
Figure 2: Marking Area for Serial Numbers ......................................................... 29
Figure 3: Data Contacts ......................................................................................... 30
Figure 4: Power Jumper Contacts ......................................................................... 31
Figure 5: CAGE CLAMP
®
connections ................................................................ 32
Figure 6: Service Interface (Closed and Open Flap) ............................................. 33
Figure 7: Network Connections – X1, X2 ............................................................. 34
Figure 8: RS-232/RS-485 – X3 Communication Connection ............................... 35
Figure 9: Termination with DTE-DCE Connection (1:1) ..................................... 36
Figure 10: Termination with DTE-DTE Connection (Cross-Over) ...................... 36
Figure 11: RS-485 Bus Termination ..................................................................... 37
Figure 12: CANopen – X4 Fieldbus Connection .................................................. 38
Figure 13: CANopen Standard Bus Termination .................................................. 39
Figure 14: PROFIBUS DP – X5 Fieldbus Connection ......................................... 40
Figure 15: PROFIBUS Line Termination Based on EN 50170 ............................ 41
Figure 16: Power Supply Indicating Elements ...................................................... 42
Figure 17: Fieldbus/System Indicating Elements .................................................. 43
Figure 18: Indicating Elements, Memory Card Slot ............................................. 44
Figure 19: Indicating Elements, RJ-45 Jacks ........................................................ 45
Figure 20: Mode Selector Switch .......................................................................... 46
Figure 21: Reset Button ......................................................................................... 47
Figure 22: Slot for SD Memory Card .................................................................... 48
Figure 23: Schematic diagram ............................................................................... 49
Figure 24: Spacing ................................................................................................. 75
Figure 25: Release Tab of Controller .................................................................... 77
Figure 26: Insert I/O Module (Example) ............................................................... 78
Figure 27: Snap the I/O Module into Place (Example) ......................................... 78
Figure 28: Connecting a Conductor to a CAGE CLAMP
®
................................... 79
Figure 29: Fuse Protection of the Electronic Circuit Power Supply ..................... 80
Figure 30: “Open DHCP”, Example Figure .......................................................... 83
Figure 31: CBM Starting Screen ........................................................................... 84
Figure 32: CBM – Selecting “Networking” .......................................................... 85
Figure 33: CBM – Selecting “TCP/IP” ................................................................. 85
Figure 34: CBM – Selecting “IP address” ............................................................. 85
Figure 35: CBM – Selecting the IP Address ......................................................... 86
Figure 36: CBM – Entering a New IP Address ..................................................... 86
Figure 37: “WAGO Ethernet Settings” – Starting Screen (Example) ................... 87
Figure 38: “WAGO Ethernet Settings” – “Network” Tab .................................... 88
Figure 39: Example of a Function Test ................................................................. 89
Figure 40: Entering Authentication ....................................................................... 93
Figure 41: Password Reminder ............................................................................. 94
Figure 42: WBM Browser Window (Example) .................................................... 96
Figure 43: WBM Status Information (Example) ................................................... 96
Figure 44: CBM main menu (example) .............................................................. 152
Figure 45: “WAGO ETHERNET Settings” – Start Screen ................................ 202
Figure 46: “WAGO ETHERNET Settings” – Communication Link .................. 203
Figure 47: “WAGO ETHERNET Settings” – Identification Tab (Example) ..... 204
Figure 48: “WAGO ETHERNET Settings” – Network Tab ............................... 205

WAGO I/O-SYSTEM 750 Specifications

General

Brand	WAGO
Model	I/O-SYSTEM 750
Category	I/O Systems
Language	English