YASKAWA A1000 HHP

KEB Operation Using L2-02 and KEB Input............................... 137
KEB Operation Using L2-10, Without KEB Input......................... 137
KEB Operation Using L2-10 and KEB Input............................... 138
KEB Operation Wiring Example ............................................. 138
KEB Ride-Thru End Detection ............................................... 136
KEB Ride-Thru Function...................................................... 103
KEB Ride-Thru Start........................................................... 135
kWh............................................................................... 303
kWh, Lower 4 Digits ........................................................... 303
kWh, Upper 5 Digits ........................................................... 303
kWh Monitor Initialization .................................................... 166
kWh Monitor Initial Value Selection ........................................ 294
L
L3-01 through L3-06 ........................................................... 178
L3-02 ............................................................................. 232
L3-04 ............................................................................. 230
L3-11 ............................................................................. 178
L7-01 through L7-04 ........................................................... 178
L7-06 ............................................................................. 178
L7-07 ............................................................................. 178
Language Selection...............................................................10
Leakage Inductance Alarm .................................................... 217
Leakage Inductance Error ..................................................... 220
LED Check ...................................................................... 302
LF ................................................................................. 189
LF2 ............................................................................... 190
LF3 ............................................................................... 190
Line-to-Line Resistance Error................................................. 218
LO/RE (LOCAL/REMOTE) Key Function Selection.......................24
LOCAL/REMOTE Key Function Selection ................................ 292
LOCAL/REMOTE Run Selection..............................................24
Loopback Test................................................................... 326
Loss of Reference Function ................................................... 146
LT-1 .............................................................................. 207
LT-2 .............................................................................. 207
LT-3 .............................................................................. 208
LT-4 .............................................................................. 208
M
Magnetic Flux Compensation Value ...........................................27
Maintenance Monitors ......................................................... 171
Maintenance Monitor Settings ................................................ 165
Master Speed Reference Lower Limit .........................................62
Maximum Output Frequency....................................................76
Maximum Voltage................................................................76
MC/FAN power malfunction.................................................. 201
Mechanical Weakening Detection............................................ 113
Mechanical Weakening Detection 1 ................................... 196, 209
Mechanical Weakening Detection 2 ......................................... 200
Mechanical Weakening Detection Operation ......................... 150, 287
Mechanical Weakening Detection Speed Level ...................... 150, 287
Mechanical Weakening Detection Start Time ........................ 151, 287
Mechanical Weakening Detection Time............................... 151, 287
MEMOBUS/Modbus Comm. Test Mode Complete ....................... 210
MEMOBUS/Modbus Communication Error.......................... 184, 204
MEMOBUS/Modbus Communications Reference......................... 303
MEMOBUS/Modbus communication terminal and S2 DIP switch ..... 318
MEMOBUS/Modbus Communication Test Mode Error.................. 211
MEMOBUS/Modbus Data Table............................................. 328
MEMOBUS/Modbus Error Code
............................................ 299
MEMOBUS/Modbus Error Codes ........................................... 345
MEMOBUS/Modbus Setup Parameters ..................................... 319
MEMOBUS/Modbus Specifications ......................................... 315
Message Format................................................................. 324
MessageID (INV)............................................................... 300
MessageID (OPR) .............................................................. 300
Middle Output Frequency .......................................................76
Middle Output Frequency 2 .....................................................76
Middle Output Frequency Voltage .............................................76
Middle Output Frequency Voltage 2...........................................76
Mid Output Voltage A ......................................................... 176
Minimum KEB Time........................................................... 140
Minimum Output Frequency ....................................................76
Minimum Output Frequency Voltage..........................................76
Minimum Output Voltage ..................................................... 176
Minimum Wait Time for Sending Messages................................ 323
Minor Alarms ................................................................... 179
Minor Fault ...................................................................... 218
Minor Fault and Alarm Displays ............................................. 181
Minor Faults ..................................................................... 179
Minor Faults and Alarms ...................................................... 179
Model, Voltage Class, Capacity Mismatch.................................. 223
Momentary Power Loss Minimum Baseblock Time................. 139, 283
Momentary Power Loss Operation Selection ...........................31, 283
Momentary Power Loss Ride-Thru .......................................... 134
Momentary Power Loss Ride-Thru Time ............................. 139, 283
Momentary Power Loss Voltage Recovery Ramp Time ............ 139, 283
Monitor Parameters....................................................... 121, 298
Most Recent Fault .............................................................. 302
Motor 1/Motor 2 Selection .................................................... 168
Motor 1 Parameters...............................................................77
Motor 2 ASR Gain Switching Frequency .....................................57
Motor 2 ASR Integral Limit.....................................................57
Motor 2 ASR Integral Time .....................................................56
Motor 2 ASR Limit...............................................................57
Motor 2 ASR Primary Delay Time Constant .................................57
Motor 2 ASR Proportional Gain................................................56
Motor 2 Base Frequency.........................................................80
Motor 2 Base Voltage ............................................................80
Motor 2 Control Mode Selection ...............................................80
Motor 2 Iron Loss.................................................................82
Motor 2 Leakage Inductance ....................................................82
Motor 2 Line-to-Line Resistance ...............................................82
Motor 2 Max Output Frequency ................................................80
Motor 2 Max Voltage ............................................................80
Motor 2 Mechanical Loss........................................................82
Motor 2 Mid Output Frequency.................................................80
Motor 2 Mid Output Frequency 2 ..............................................80
Motor 2 Mid Output Frequency Voltage ......................................80
Motor 2 Mid Output Frequency Voltage 2 ....................................80
Motor 2 Minimum Output Frequency..........................................80
Motor 2 Minimum Output Frequency Voltage ...............................80
Motor 2 Motor Iron-Core Saturation Coefficient 1 ..........................82
Motor 2 Motor Iron-Core Saturation Coefficient 2 ..........................82
Motor 2 Motor Poles .............................................................82
Motor 2 Parameters...............................................................81
Motor 2 Rated Current ...........................................................81
Motor 2 Rated No-Load Current................................................81
Motor 2 Rated Power.............................................................83
Index
YASKAWA ELECTRIC SIEP YEAHHP 01B YASKAWA AC Drive – A1000 HHP Programming Manual
351