YASKAWA GA800

1074 YASKAWA SIEPC71061737D GA800 Drive Technical Reference
Protection Functions ............................................. 1005
rUn ........................................................................ 399
RUN
LED status........................................................... 165
Run command
LOCAL/REMOTE Run selection................................ 718
Switching between LOCAL/REMOTE ......................... 718
Run Command at Power Up ........................................... 728
Run Command Selection 2
Switching between LOCAL/REMOTE ......................... 727
RUN indicator ..................................................... 159, 162
RUN key ................................................................. 159
S
S-curve characteristics
Parameter ............................................................ 775
Sampling time setting
Data log.............................................................. 208
SC ......................................................................... 386
SCF........................................................................ 387
SE ......................................................................... 399
SEr ........................................................................ 387
Serial communication terminals
MEMOBUS/Modbus Communications ......................... 118
Set date and time
Operation ............................................................ 201
Set time
Operation ............................................................ 201
Setup Wizard
Operation ............................................................ 203
Short Circuit Braking
Parameter ............................................................ 729
Side-by-side
Derating...................................................... 506, 1003
Simple Positioning Stop................................................ 809
Slip compensation
Parameter ............................................................ 775
Softcharge Relay Maintenance Set ................................. 1050
Software Current Limit Selection
Protective function ............................................... 1002
Software version
Display procedure .................................................. 210
Speed Agreement
Parameter ............................................................ 985
Speed Detection
Parameter ............................................................ 985
Speed Estimation Speed Search....................................... 734
Speed limit
Parameter ............................................................ 810
Speed Search function
Operation during momentary power loss........................ 970
Parameter ............................................................ 732
Stall Prevention function
Parameter ............................................................ 975
Stationary Auto-Tuning
Induction Motor .................................................... 215
PM Motors .......................................................... 216
Precautions .......................................................... 222
Stationary Auto-Tuning for Line-to-Line Resistance .............. 215
Precautions .......................................................... 223
Stator resistance Auto-Tuning......................................... 216
Precautions .......................................................... 223
STo ........................................................................ 399
SToF ...................................................................... 399
Stop command
LOCAL/REMOTE Run selection................................ 718
STOP key................................................................. 159
STOP Key Function Selection....................................... 1043
Stopping Method Selection ............................................ 719
STPo ...................................................................... 387
Surge protective device
Connection .......................................................... 144
SvE........................................................................ 387
T
Temperature
Environment.......................................................... 36
Terminal block........................................................... 118
Configuration of main circuit terminal block.................... 75
Control circuit terminal block functions......................... 113
I/O terminals function selection switches ....................... 122
Terminal function selection ............................................ 125
Terminal A1................................................... 122, 125
Terminal A2................................................... 122, 125
Terminal A3................................................... 122, 126
Terminal AM.................................................. 122, 126
Terminal FM .................................................. 122, 126
Terminal screw
Screwdriver........................................................... 16
Termination resistor
Setting switch ....................................................... 127
Test run
Checklist............................................................. 234
Fine tuning .......................................................... 226
Procedure ............................................................ 167
Procedure for no-load test run .................................... 224
Procedure for test run with actual load .......................... 224
Thermal overload relay
Connection .......................................................... 141
Tightening torque
Control circuit terminals........................................... 119
Main circuit terminals............................................... 84
TiM
Fault .................................................................. 387
Minor Fault.......................................................... 399
Timer function
Parameter ............................................................ 742
Torque compensation
Parameter ............................................................ 810
Torque Compensation
Parameter ............................................................ 780
Torque Control
Parameter ............................................................ 809
Switching to/from Speed Control ................................ 812
Torque limit function
Parameter ............................................................ 995
Torque reference
Parameter ............................................................ 810
Trend Plot
Monitors ............................................................. 182
Troubleshooting
Code Displayed..................................................... 353
No Code Displayed................................................. 416
Troubleshooting without Fault Display .............................. 416
TrPC....................................................................... 399
Tuning .................................................................... 769