11.10 H: Terminal Functions
612 YASKAWA SIEPC71061737D GA800 Drive Technical Reference
No.
(Hex.)
Name Description
Default
(Range)
Ref.
H6-03
(042E)
RUN
Terminal RP Function
Gain
Sets the gain used when the function in H6-01 [Terminal RP Pulse Train Function] is input
to terminal RP.
100.0%
(0.0 - 1000.0%)
951
H6-04
(042F)
RUN
Terminal RP Function
Bias
Sets the bias used when the function in H6-01 [Terminal RP Pulse Train Function] is input
to terminal RP. Sets a value at the time when the pulse train is 0 Hz.
0.0%
(-100.0 - 100.0%)
951
H6-05
(0430)
RUN
Terminal RP Filter Time
Sets the time constant for the pulse train input primary delay filters.
0.10 s
(0.00 - 2.00 s)
952
H6-06
(0431)
RUN
Terminal MP Monitor
Selection
Sets a function for pulse train monitor output terminal MP. Sets the “x-xx” part of the Ux-xx
monitor.
102
(000, 031, 101, 102, 105,
116, 501, 502, 801 - 809,
821 - 825, 831 - 839, 851
- 855)
952
H6-07
(0432)
RUN
Terminal MP Frequency
Scaling
Sets the frequency of the pulse train output signal used when the monitor set with H6-06
[Terminal MP Monitor Selection] is 100%.
1440 Hz
(0 - 32000 Hz)
953
H6-08
(043F)
Terminal RP Minimum
Frequency
Sets the minimum frequency of the pulse train signal that terminal RP can detect.
0.5 Hz
(0.1 - 1000.0 Hz)
953
H6-09
(156E)
Voltage Phase Sync MP
Selection
Set whether to output the pulse synchronized with drive output voltage phase from the
pulse train monitor output terminal MP. This parameter is only enabled when H6-06 = 102
[Terminal MP Monitor Selection = Output Frequency] and H6-07 = 0 [Terminal MP
Frequency Scaling = 0 Hz].
0 : Disabled
1 : Enabled
0
(0, 1)
953
◆ H7: Virtual MFIO selection
No.
(Hex.)
Name Description
Default
(Range)
Ref.
H7-00
(116F)
Expert
Virtual MFIO selection
Sets the function to enable and disable the virtual I/O function. Set this parameter to 1 to
operate the virtual I/O function.
0 : Disabled
1 : Enabled
0
(0, 1)
954
H7-01
(1185)
Expert
Virtual Multi-Function
Input 1
Sets the function that enters the virtual input set in H7-10 [Virtual Multi-Function Output
1].
Note:
1B [Programming Lockout] and 11B [Inverse Input of 1B] are not available.
F
(1 - 19F)
954
H7-02
(1186)
Expert
Virtual Multi-Function
Input 2
Sets the function that enters the virtual input set in H7-12 [Virtual Multi-Function Output
2].
Note:
1B [Programming Lockout] and 11B [Inverse Input of 1B] are not available.
F
(1 - 19F)
954
H7-03
(1187)
Expert
Virtual Multi-Function
Input 3
Sets the function that enters the virtual input set in H7-14 [Virtual Multi-Function Output
3].
Note:
1B [Programming Lockout] and 11B [Inverse Input of 1B] are not available.
F
(1 - 19F)
954
H7-04
(1188)
Expert
Virtual Multi-Function
Input 4
Sets the function that enters the virtual input set in H7-16 [Virtual Multi-Function Output
4].
Note:
1B [Programming Lockout] and 11B [Inverse Input of 1B] are not available.
F
(1 - 19F)
955
H7-10
(11A4)
Expert
Virtual Multi-Function
Output 1
Sets the function for virtual digital output 1.
F
(0 - 1A7)
955
H7-11
(11A5)
Expert
Virtual Output 1 Delay
Time
Sets the minimum ON time for virtual digital output 1.
0.1 s
(0.0 - 25.0 s)
955
To Next Page
Loading...
