Parameter List
11
11.13 o: Keypad-Related Settings
YASKAWA SIEPC71061737D GA800 Drive Technical Reference 633
11.13 o: Keypad-Related Settings
◆ o1: Keypad Display
No.
(Hex.)
Name Description
Default
(Range)
Ref.
o1-01
(0500)
RUN
User Monitor Selection
Sets the U monitor for the Drive Mode. This parameter is only available with an LED
keypad.
106
(104 - 855)
1036
o1-02
(0501)
RUN
Monitor Selection at
Power-up
Sets the monitor item that the keypad screen shows after you energize the drive. Refer to
“U: Monitors” for information about the monitor items that the keypad screen can show.
This parameter is only available with an LED keypad.
1 : Frequency Reference (U1-01)
2 : Direction
3 : Output Frequency (U1-02)
4 : Output Current (U1-03)
5 : User Monitor (o1-01)
1
(1 - 5)
1036
o1-03
(0502)
Frequency Display Unit
Selection
Sets the display units for the frequency reference and output frequency.
0 : 0.01 Hz
1 : 0.01% (100% = E1-04)
2 : min
-1
(r/min) units
3 : User Units (o1-10 & o1-11)
Determined by A1-02
(0 - 3)
1036
o1-04
(0503)
V/f Pattern Display Unit
Sets the setting unit for parameters that set the V/f pattern frequency.
0 : Hz
1 : min
-1
(r/min) units
Determined by A1-02
(0, 1)
1037
o1-05
(0504)
RUN
LCD Contrast
Adjustment
Sets the contrast of the LCD display on the keypad.
5
(0 - 10)
1038
o1-10
(0520)
User Units Maximum
Value
Sets the value that the drive shows as the maximum output frequency.
Determined by o1-03
(1 - 60000)
1038
o1-11
(0521)
User Units Decimal
Position
Sets the number of decimal places for frequency reference and monitor values.
0 : No Decimal Places (XXXXX)
1 : One Decimal Places (XXXX.X)
2 : Two Decimal Places (XXX.XX)
3 : Three Decimal Places (XX.XXX)
Determined by o1-03
(0 - 3)
1038
o1-24
(11AD)
RUN
Custom Monitor 1
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the first line. The registered
monitor is also used for different monitor displays of bar graph, analog meter, and
waveform.
101
(0, 101 - 999)
1038
o1-25
(11AE)
RUN
Custom Monitor 2
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the second line. The
registered monitor is also used for different monitor displays of bar graph and waveform.
102
(0, 101 - 999)
1038
o1-26
(11AF)
RUN
Custom Monitor 3
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the third line. The registered
monitor is also used for the monitor display of the bar graph.
103
(0, 101 - 999)
1038
o1-27
(11B0)
RUN
Custom Monitor 4
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the fourth line.
0
(0, 101 - 999)
1038
o1-28
(11B1)
RUN
Custom Monitor 5
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the fifth line.
0
(0, 101 - 999)
1038
o1-29
(11B2)
RUN
Custom Monitor 6
You can select a maximum of 12 monitors as user monitors and set them to parameters o1-
24 to o1-35. This parameter sets the user monitor to show on the sixth line.
0
(0, 101 - 999)
1038
To Next Page
Loading...
