S1 ................................................................................. 107
s1/l21 ...............................................................................96
S2 ................................................................................. 107
S3 ................................................................................. 107
S4 ................................................................................. 107
S5 ................................................................................. 107
S6 ................................................................................. 107
S7 ................................................................................. 107
S8 ................................................................................. 107
Safe Disable Circuit ............................................................ 673
Safe Disable Input Function................................................... 672
Safe Disable Inputs ............................................................. 107
Safe Disable Monitor Output Function and Digital Operator Display... 674
Safety Circuit Fault............................................................. 381
Safety Monitor Output ......................................................... 108
SC................................................................................. 107
SCF ............................................................................... 381
SE ................................................................................. 391
Search Operation Voltage Limit .............................................. 219
Self-Diagnostics................................................................. 285
SEr ................................................................................ 381
Serial Communications Cable Connection Terminals (TB5) ............. 614
Serial Communication Terminals............................................. 108
Serial Communication Transmission Error ................................. 385
Serviceable Parts................................................................ 452
Setup Group ..................................................................... 144
Setup Group Parameters ....................................................... 145
Setup Mode ...................................................................... 141
Shielded Twisted-Pair Cables................................................. 111
Simple Motor Setup Using V/f Control...................................... 148
Simplified Setup Using the Setup Group .................................... 141
Sinking/Sourcing Mode for Digital Inputs .................................. 107
Slave Address ................................................................... 623
Slip Compensation.............................................................. 224
Slip Compensation Gain ....................................................... 224
Slip Compensation Limit ...................................................... 225
Slip Compensation Primary Delay Time .................................... 225
Slip Compensation Selection during Regeneration ........................ 225
SMRA Series SPM Motor Settings .......................................... 594
SN................................................................................. 107
Snubber Discharge Resistor Overheat ....................................... 381
Soft Charge Bypass Relay Maintenance..................................... 577
Soft Charge Bypass Relay Maintenance Time.............................. 389
Soft CLA Selection............................................................. 556
Software Current Limit Selection ............................................ 330
Software No. (Flash) ........................................................... 574
Software No. (ROM) ........................................................... 574
Software version ..................................................................34
SoH ............................................................................... 381
SoH Alarm Selection during bb............................................... 333
Speed/Torque Control Switchover Time .................................... 249
Speed Agree 1 Time Chart .................................................... 289
Speed Agree 2 Time Chart .................................................... 293
Speed Agree Detection Level ........................................... 321, 552
Speed Agree Detection Level (+/-)..................................... 321, 552
Speed Agree Detection Selection....................................... 321, 552
Speed Agree Detection Width .......................................... 321, 552
Speed Agree Detection Width (+/-) .................................... 321, 552
Speed Control Accuracy ....................................................... 482
Speed Control Integral Time 1................................................ 390
Speed Control Loop Auto-Tuning
............................................ 160
Speed Control Proportional Gain 1........................................... 390
Speed Control Range........................................................... 482
Speed Deviation........................................................... 265, 369
Speed Feedback Detection Control (AFR) Gain ..................... 335, 558
Speed Feedback Detection Control (AFR) Time Constant 1 ....... 335, 558
Speed Feedback Detection Control Gain (for PM Motors) ......... 340, 561
Speed Limit...................................................................... 248
Speed Limitation................................................................ 246
Speed Limit Bias.......................................................... 246, 248
Speed Limit Selection.......................................................... 248
Speed Response ................................................................. 482
Speed Search Deceleration Time ............................................. 200
Speed Search Delay Time ..................................................... 200
Speed Search Detection Compensation Gain ............................... 201
Speed Search Induced Voltage Level ........................................ 202
Speed Search Method Selection .............................................. 202
Speed Search Restart Current Level.......................................... 201
Speed Search Restart Detection Time........................................ 201
Speed Search Selection at Start ............................................... 200
Speed Search Selection when Run Command Is Given during Uv ...... 203
Speed Search Wait Time....................................................... 202
SrC................................................................................ 381
Srr................................................................................. 381
SSR1 Series IPM Motor Settings............................................. 595
SST4 Series IPM Motor Settings ............................................. 602
Stall Prevention ................................................................. 316
Stall Prevention Detection Time.............................................. 320
Stall Prevention Level during Acceleration/Deceleration................. 317
Stall Prevention Level during Run ..................................... 319, 551
Stall Prevention Limit during Acceleration/Deceleration ................. 316
Stall Prevention Selection during Acceleration....................... 316, 550
Stall Prevention Selection during Deceleration....................... 318, 551
Stall Prevention Selection during Run ................................. 319, 551
Standard Connection Diagram ..................................................78
Standards......................................................................... 483
Start Condition Selection at Closed Loop Vector Control ................ 195
Starting Torque.................................................................. 482
Start Speed Search Select...................................................... 202
Start-Up Flowcharts ............................................................ 146
Station Address Setting Error ................................................. 384
Stationary Auto-Tuning........................................................ 162
Stationary Auto-Tuning 2...................................................... 157
Stationary Auto-Tuning 3...................................................... 157
Stationary Auto-Tuning for Line-to-Line Resistance...................... 157
Stator Resistance Error......................................................... 400
STo ............................................................................... 381
STOP button Input.............................................................. 398
STOP Key ....................................................................... 135
STOP Key Function Selection .......................................... 346, 563
Stopping Method after Communication Error .............................. 617
Stopping Method Selection.................................................... 189
Storage Temperature ........................................................ 58, 59
Suppression Auxiliary Frequency ............................................ 335
Suppression Frequency ........................................................ 335
Surrounding Area ............................................................ 58, 59
SvE ............................................................................... 382
Switching Between LOCAL and REMOTE ................................ 145
Switching Between Torque and Speed Control............................. 247
Index
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual
701
To Next Page
Loading...
