YASKAWA U1000 - Page 700

PM Motor Code................................................................. 261
PM Motor Code Selection ..................................................... 167
PM Motor Control Tuning..................................................... 339
PM Motor d-Axis Inductance ................................................. 168
PM Motor Induced Voltage Constant........................................ 168
PM Motor Parameter Settings................................................. 158
PM Motor q-Axis Inductance ................................................. 168
PM Motor Rated Current ...................................................... 167
PM Motor Rated Voltage ...................................................... 167
PM Motor Settings ............................................................. 167
PM Motor Stator Resistance .................................................. 168
PM Motor Type ................................................................. 167
PM Rotational Auto-Tuning................................................... 158
PM Stationary Auto-Tuning................................................... 158
PM Stationary Auto-Tuning for Stator Resistance ......................... 158
Polarity Compensation Gain 3 ................................................ 339
Polarity Compensation Gain 4 ................................................ 339
Polarity Switch for Initial Polarity Estimation Timeout................... 263
Pole Attraction Current ........................................................ 339
Power Consumption Output Unit Selection................................. 296
Power Detection Filter Time .................................................. 219
Power Factor Control Selection............................................... 235
Powering Up the Drive......................................................... 153
Power Ratings (Three-Phase 200 V Class)............................ 477, 478
Power Ratings (Three-Phase 400 V Class)...................... 479, 480, 481
Power Supply and Control Circuit............................................ 128
Power Supply Frequency Fault ............................................... 372
Power Supply Overvoltage .................................................... 367
Power Supply Terminal Block TB1 Wiring................................. 126
Power Supply Undervoltage................................................... 367
Power Unit Price................................................................ 349
Predefined V/f Patterns ........................................................ 251
Preparing the Ends of Shielded Cables ...................................... 111
Preset Reference Timing Diagram ........................................... 238
Previous Fault ................................................................... 574
PROFIBUS-DP Clear Mode Selection ...................................... 274
PROFIBUS-DP Data Format Selection...................................... 274
PROFIBUS-DP Node Address ............................................... 273
PROFIBUS-DP Parameters ................................................... 273
Programming Mode ...................................................... 140, 141
Proportional Gain Setting (P) ................................................. 210
PTC ............................................................................... 303
Pull-In Current (for PM Motors)........................................ 341, 561
Pull-In Current Compensation Time Constant (for PM Motors) ... 340, 561
Pull-In Current Level for PM Motor Tuning................................ 169
Pull-Out Detection.............................................................. 381
Pulse Monitor Selection Error ................................................ 396
Pulse Output Connection Using External Voltage Supply ................ 117
Pulse Output Connection Using Internal Voltage Supply................. 116
Pulse Train Input/Output....................................................... 287
Pulse Train Input Bias.......................................................... 307
Pulse Train Input Filter Time ................................................. 307
Pulse Train Input Gain ......................................................... 307
Pulse Train Input Minimum Frequency...................................... 307
Pulse Train Input Scaling ...................................................... 307
Pulse Train Input Terminal RP Function Selection ........................ 306
Pulse Train Monitor Scaling .................................................. 307
Pulse Train Monitor Selection ................................................ 307
Q
q-Axis ACR Output ............................................................ 580
q-Axis Current Compensation Method when Output Voltage Is Limited220
R
R-.................................................................................. 108
R/L1 ................................................................................96
R+................................................................................. 108
r1/l11 ...............................................................................96
Rated Current Depending on Carrier Frequency ........................... 486
Rated Current Setting Alarm .................................................. 397
Rated Slip Error................................................................. 399
rdEr ............................................................................... 403
READ ............................................................................ 348
rEAd .............................................................................. 403
Reading Drive MEMOBUS/Modbus Register Contents .................. 625
Reading Parameter Settings ................................................... 403
Reattaching the Digital Operator ...............................................92
Reattaching the Front Cover ....................................................94
Reattaching the Terminal Cover ................................................90
REMOTE ........................................................................ 145
Removing the Cooling Fan .................................................... 427
Removing the Digital Operator .................................................92
Removing the Front Cover ......................................................92
Removing the Protective Cover.................................................95
Removing the Terminal Cover..................................................89
Replacement Parts .............................................................. 421
Replacing the Drive ............................................................ 452
Reset Communication Parameters............................................ 271
RESET Key...................................................................... 135
Resistance Tuning Error ....................................................... 397
Response Messages from Drive to Master .................................. 622
Reverse Direction Output Example Time Chart............................ 295
Reverse Operation Selection .................................................. 192
Reverse Prohibited Error....................................................... 400
Reverse Regenerative Torque Limit ................................... 327, 555
Reverse Torque Limit .................................................... 327, 555
Rotational Auto-Tuning.................................................. 157, 161
Rotational Auto-Tuning for V/f Control..................................... 157
RP................................................................................. 108
RS-422 Interface ................................................................ 616
RS-485 Interface ................................................................ 615
RTS Control Selection ......................................................... 618
rUn................................................................................ 391
Run Command/Frequency Reference Source Selection Error............ 394
Run Command at Power Up................................................... 195
Run Command Method Selection ............................................ 620
Run Command Selection 1 .............................................. 188, 494
Run Command Selection 2 .................................................... 195
Run command selection while in Programming Mode .................... 194
Run Command Source Selection ............................................. 578
RUN Key ........................................................................ 135
RUN LED........................................................................ 137
RUN Light ....................................................................... 135
Run Speed after Soft Starter at Previous Fault.............................. 575
S
S-.................................................................................. 108
S/L2.................................................................................96
S+ ................................................................................. 108
Index
700
YASKAWA ELECTRIC SIEP C710636 04D U1000 Industrial MATRIX Drive Technical Manual