Zeiss Axio Imager 2 - Page 4

ZEISS Contents Axio Imager 2
4 430000-7544-001 01/2016
3.20 Attaching the condenser carrier to the transmitted-light / reflected-light stage carrier .......... 50
3.21 Changing the fine-drive knob or the fine-drive disk on the stand ........................................ 50
3.22 Insert the filter in the double filter wheel ............................................................................ 51
3.22.1 Double filter wheel, manual ............................................................................................... 51
3.22.2 Double filter wheel, motorized .......................................................................................... 52
3.23 Axio Imager.Z2 / Z2m High-performance Focus .................................................................. 53
3.23.1 Activating the high-performance focus .............................................................................. 53
3.23.2 Deactivating the high-performance focus ........................................................................... 54
3.24 Mounting the TFT display on the motorized stand .............................................................. 54
3.25 Attaching the TFT display to the docking station ................................................................ 55
3.26 Installing the focus linear sensor ........................................................................................ 56
3.27 Assembling the multidiscussion equipment ........................................................................ 56
3.28 Connecting to power ........................................................................................................ 57
3.28.1 Coded stand ..................................................................................................................... 57
3.28.2 Motorized stand ................................................................................................................ 57
3.29 HAL 100 halogen illuminator ............................................................................................. 58
3.29.1 Attaching the HAL 100 halogen illuminator ....................................................................... 58
3.29.2 Separate power supply of the HAL 100 halogen illuminator for reflected light ..................... 59
3.29.3 Adjusting the HAL 100 halogen illuminator ........................................................................ 60
3.29.4 Replacing the HAL 100 halogen lamp ................................................................................ 61
3.30 Installing the LED illuminator for transmitted light .............................................................. 62
3.31 VIS-LED attachment lamp for transmitted light ................................................................... 64
3.31.1 The VIS-LED attachment lamp is only intended for use with transmitted light. ..................... 64
3.31.2 Adjusting the VIS-LED attachment lamp ............................................................................. 65
3.32 Mounting the microLED attachment lamp for transmitted light ........................................... 65
3.33 HBO 100 illuminator.......................................................................................................... 66
3.33.1 Inserting the HBO 103 W/2 mercury vapor short-arc lamp .................................................. 66
3.33.2 Attaching the HBO 100 illuminator .................................................................................... 66
3.33.3 Aligning the HBO 100 illuminator ...................................................................................... 67
3.33.4 Setting up the switching mirror for two illuminators (manual or motorized) ........................ 68
3.34 Electrical connections on the rear of the microscope........................................................... 69
3.34.1 Coded stand ..................................................................................................................... 69
3.34.2 Motorized stand ................................................................................................................ 69
3.35 Mount sample stage.......................................................................................................... 70
3.35.1 Fixed mechanical stage 75x50 R ........................................................................................ 70
3.35.2 Rotatable mechanical stage 75x50/240° R .......................................................................... 71
3.35.3 Adjusting the stage drive length on the ergonomic drive .................................................... 72
3.35.4 Removing and attaching additional sleeves ........................................................................ 73
3.35.5 Adjusting the action (torque) of the two drive knobs of the ergonomic drive ....................... 73
3.35.6 Changing the specimen holder .......................................................................................... 74
3.36 Rotary stage Pol ................................................................................................................ 74
3.36.1 Removing the rotary stage Pol ........................................................................................... 74
3.36.2 Attaching rotary stage Pol ................................................................................................. 75
3.36.3 Centering rotary stage Pol ................................................................................................. 75
3.36.4 Centering objectives .......................................................................................................... 76
3.37 Mechanical stage 75x50 mot. CAN .................................................................................... 77
3.37.1 Assembling and connecting 75x50 mot. CAN mechanical stage with coaxial drive .............. 77