Accedian EtherNID EE

To Next Page

To Previous Page

6: Alarms

• Critical: A service-affecting condition has occurred that requires immediate corrective action.

Service affecting

Specify if the alarm will be displayed as service affecting or non-service affecting.

Description

Textual description of the alarm.

Main Page

Default Chapter3
- Table of Contents3
Introduction9
Introducing the Ethernid9
- Features and Benefits10
- Applications10
Application Scenario11
- About this Scenario11
Hardware Installation12
Hardware Overview12
- Front Panel13
- Ethernet Ports13
- SFP Ports13
- Port Functionality13
- Status Lights16
- Rear Panel16
- Port/Connectors16
- Status Light17
- Buttons17
Mounting Options18
- Wall Mounting18
- Desktop Installation18
- Rack Mounting19
- Grounding the Ethernid19
- Ethershelf20
- Grounding the Ethershelf20
- Dimensions21
Powering the Ethernid22
- DC Power Adapter22
- 48V DC from the 12 Unit Ethershelf22
- 24V or 48V DC from the Terminal Block Adapter23
- 48V DC Via Discrete Power Cord23
Restarting25
Resetting to Factory Defaults25
Management & Configuration26
About the Management Web Interface26
- Starting the Management Web Interface26
- Managing Web Interface Accounts26
- Managing Accounts27
- Changing the Default Administrator Password27
- Lost Administrator Password27
- Creating Additional Accounts28
DNS Settings29
- Use DHCP Results29
- Set DNS Manually29
Configuring Interfaces30
- Creating or Editing an Interface30
- Interface Settings31
- Beacon Settings33
- Auto Interface Settings34
- Discovery Settings34
- Advertisement Settings35
- Discovery Inventory36
Routes37
- Adding a Route37
- Route Parameters38
Syslog Options39
- Syslog Parameters39
- Remote Syslog Configuration40
Setting the System Date and Time41
- Date and Time Settings42
Timezone and Daylight Saving43
SNMP Settings44
- SNMP Parameters45
- SNMP Trap Receivers46
- SNMP Trap Receivers Parameters47
- SNMP Trap Configuration Parameters48
History Buckets49
- Local Configuration49
Remote Retrieval of History Buckets50
- Scheduling and File Transfer Configuration51
Certificate Management54
Ping and Traceroute55
General System Settings56
- Aggregator Operation Modes57
Session Management59
- Management Parameters59
- Current Sessions59
Firmware Upgrade61
- Configuration Maintenance61
- System Control62
Session Configuration63
- Session Parameters63
Session RADIUS65
- RADIUS Parameters65
Show CPU Usage67
- CPU Usage Parameters67
Management Bridge68
- Configuration Procedure68
Port Configuration70
Port List and Port Status70
- Port Configuration and Status74
- Port Options74
- Fault Propagation75
Configuring Port Settings76
- Port Parameters78
Port Statistics81
PHY Auto-Negotiation Configuration82
- PHY Parameters84
SFP Information85
- Monitoring Information86
- SFP Thresholds87
- Temperature87
- VCC88
- Laser Bias Current88
- Tx Power88
- Rx Power89
- SFP Memory and Monitor Memory90
Cable Verification91
- Testing a Cable91
Monitoring & Filtering93
Service Mapping93
- Viewing Cos Profiles93
- Configuring a Cos Profile94
- Cos Profile Parameters95
- Assigning a Cos Profile to a Policy96
- Viewing Bandwidth Regulator Sets96
- Configuring a Bandwidth Regulator Set97
- Bandwidth Regulator Set Parameters97
- Assigning a Bandwidth Regulator Set to a Policy98
Layer-2 Protocol Tunneling99
- Adding a New L2PT Rule101
- L2PT Rule Settings101
Traffic Policies and Monitoring104
- Configuring a Traffic Policy105
- Policy Settings105
Traffic Filters110
- Viewing L2 Filters110
- Configuring an L2 Filter110
- L2 Filter Parameters111
- Viewing Ipv4 Filters113
- Configuring an Ipv4 Filter114
- Ipv4 Filter Parameters114
Bandwidth Policing117
- Configuring a Regulator118
- Regulator Settings118
- Assigning a Regulator to a Policy119
Alarms120
Alarm Settings120
Alarm Configuration121
- Customizing an Alarm122
Alarm Status125
Chassis Alarms126
Operations, Administration & Maintenance127
OAM Configuration127
- Configuring an OAM Instance128
- OAM Instance Parameters128
Loopbacks131
- Adding a Loopback132
- Loopback Parameters132
OAM Events135
- Transmitted and Received Event Notifications136
OAM Status138
- Detailed Status Information139
- Remote140
OAM Statistics141
- OAM Detailed Statistics Information142
Viewing RFC-2544 Generator146
- Configuring RFC-2544 Generator147
Rfc-2544146
RFC-2544 Monitor151
- Viewing RFC-2544 Monitor151
- Detailed View of RFC-2544 Monitor151
RFC-2544 Testsuite154
- Viewing RFC-2544 Testsuites154
- Detailed View of RFC-2544 Testsuites155
RFC-2544 Reports159
- Starting an RFC-2544 Testsuite159
- Viewing RFC-2544 Reports160
Performance Assurance Agent162
PAA Configuration162
- Configuring a Probe163
- PAA Parameters165
Igmp169
PAA Status171
- Detailed PAA Status172
PAA Results174
- Detailed PAA Results175
10 Traffic Shaper177
Traffic Shaper Configuration177
Traffic Shaper Statistics181
11 Cfm182
CFM Continuity Fault Management182
CFM Configuration183
CFM Statistics194
Command Line Interface196
Command Summary196
Command Syntax198
Alarms199
13 Appendix A - Alarms199
Appendix B - Mib Support203
Public Mibs203
Private Mibs205

Accedian EtherNID EE - Page 124

Table of Contents

Related product manuals