EasyManuals Logo

Cisco Catalyst 3750-E User Manual

Cisco Catalyst 3750-E
1414 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #863 background imageLoading...
Page #863 background image
37-9
Catalyst 3750-E and 3560-E Switch Software Configuration Guide
OL-9775-08
Chapter 37 Configuring QoS
Understanding QoS
The policy map can contain the police and police aggregate policy-map class configuration commands,
which define the policer, the bandwidth limitations of the traffic, and the action to take if the limits are
exceeded.
To enable the policy map, you attach it to a port by using the s
ervice-policy interface configuration
command.
You can apply a nonhierarchical policy map to a physical port or an SVI. However, a hierarchical policy
ma
p can only be applied to an SVI. A hierarchical policy map contains two levels. The first level, the
VLAN level, specifies the actions to be taken against a traffic flow on the SVI. The second level, the
interface level, specifies the actions to be taken against the traffic on the physical ports that belong to the
SVI. The interface-level actions are specified in the interface-level policy map.
For more information, see the
Policing and Marking” section on page 37-9. For configuration
information, see the “Configuring a QoS Policy” section on page 37-49.
Policing and Marking
After a packet is classified and has a DSCP-based or CoS-based QoS label assigned to it, the policing
and marking process can begin as shown in Figure 37-4.
Policing involves creating a policer that specifies the bandwidth limits for the traffic. Packets that exceed
th
e limits are out of profile or nonconforming. Each policer decides on a packet-by-packet basis whether
the packet is in or out of profile and specifies the actions on the packet. These actions, carried out by the
marker, include passing through the packet without modification, dropping the packet, or modifying
(marking down) the assigned DSCP of the packet and allowing the packet to pass through. The
configurable policed-DSCP map provides the packet with a new DSCP-based QoS label. For information
on the policed-DSCP map, see the “Mapping Tables” section on page 37-13. Marked-down packets use
the same queues as the original QoS label to prevent packets in a flow from getting out of order.
Note All traffic, regardless of whether it is bridged or routed, is subjected to a policer, if one is configured.
As a result, bridged packets might be dropped or might have their DSCP or CoS fields modified when
they are policed and marked.
You can configure policing (either individual or aggregate policers) on a physical port or an SVI. For
more information about configuring policing on physical ports, see the Policing on Physical Ports”
section on page 37-10. When configuring policy maps on an SVI, you can create a hierarchical policy
map and can define an individual policer only in the secondary interface-level policy map. For more
in
formation, see the “Policing on SVIs” section on page 37-11.
After you configure the policy map and policing actions, attach the policy to an ingress port or SVI by
u
sing the service-policy interface configuration command. For configuration information, see the
“Classifying, Policing, and Marking Traffic on Physical Ports by Using Policy Maps” section on
page 37-59, the “Classifying, Policing, and Marking Traffic on SVIs by Using Hierarchical Policy
Maps” section on page 37-64, and the “Classifying, Policing, and Marking Traffic by Using Aggregate
Policers” section on page 37-72.

Table of Contents

Other manuals for Cisco Catalyst 3750-E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750-E and is the answer not in the manual?

Cisco Catalyst 3750-E Specifications

General IconGeneral
SeriesCatalyst 3750-E
Switching Capacity32 Gbps
Stacking Bandwidth32 Gbps
StackWise PlusYes
Layer SupportLayer 3
MAC Address Table Size12, 000 entries
RAM256 MB
Flash Memory64 MB
Memory256 MB DRAM, 64 MB Flash
Operating Temperature32 to 113°F (0 to 45°C)
Ports48 10/100/1000 Ethernet ports
Form FactorRack-mountable
Jumbo Frame SupportYes
Input Voltage100 to 240 VAC
Storage Temperature-25 to 70 °C
Relative Humidity10 to 90% non-condensing

Related product manuals