EasyManuals Logo

Cisco Catalyst 3750-E User Manual

Cisco Catalyst 3750-E
1414 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #867 background imageLoading...
Page #867 background image
37-13
Catalyst 3750-E and 3560-E Switch Software Configuration Guide
OL-9775-08
Chapter 37 Configuring QoS
Understanding QoS
Mapping Tables
During QoS processing, the switch represents the priority of all traffic (including non-IP traffic) with a
QoS label based on the DSCP or CoS value from the classification stage:
During classification, QoS uses configurable mapping tables to derive a corresponding DSCP or
CoS value from a received CoS, DSCP, or IP precedence value. These maps include the
CoS-to-DSCP map and the IP-precedence-to-DSCP map. You configure these maps by using the mls
qos map cos-dscp and the mls qos map ip-prec-dscp global configuration commands.
On an ingress port configured in the DSCP-trusted state, if the DSCP values are different between
th
e QoS domains, you can apply the configurable DSCP-to-DSCP-mutation map to the port that is
on the boundary between the two QoS domains. You configure this map by using the mls qos map
dscp-mutation global configuration command.
During policing, QoS can assign another DSCP value to an IP or a non-IP packet (if the packet is
out of profile and the policer specifies a marked-down value). This configurable map is called the
policed-DSCP map. You configure this map by using the mls qos map policed-dscp global
configuration command.
Before the traffic reaches the scheduling stage, QoS stores the packet in an ingress and an egress
queue according to the QoS label. The QoS label is based on the DSCP or the CoS value in the packet
and selects the queue through the DSCP input and output queue threshold maps or through the CoS
input and output queue threshold maps. In addition to an ingress or an egress queue, the QOS label
also identifies the WTD threshold value. You configure these maps by using the mls qos srr-queue
{input | output} dscp-map and the mls qos srr-queue {input | output} cos-map global
configuration commands.
The CoS-to-DSCP, DSCP-to-CoS, and the IP-precedence-to-DSCP maps have default values that might
or
might not be appropriate for your network.
The default DSCP-to-DSCP-mutation map and the default policed-DSCP map are null maps; they map
a
n incoming DSCP value to the same DSCP value. The DSCP-to-DSCP-mutation map is the only map
you apply to a specific port. All other maps apply to the entire switch.
For configuration information, see the “C
onfiguring DSCP Maps” section on page 37-74.
For information about the DSCP and CoS input queue threshold maps, see the
Queueing and
Scheduling on Ingress Queues” section on page 37-16. For information about the DSCP and CoS output
queue threshold maps, see the “Queueing and Scheduling on Egress Queues” section on page 37-19.

Table of Contents

Other manuals for Cisco Catalyst 3750-E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 3750-E and is the answer not in the manual?

Cisco Catalyst 3750-E Specifications

General IconGeneral
SeriesCatalyst 3750-E
Switching Capacity32 Gbps
Stacking Bandwidth32 Gbps
StackWise PlusYes
Layer SupportLayer 3
MAC Address Table Size12, 000 entries
RAM256 MB
Flash Memory64 MB
Memory256 MB DRAM, 64 MB Flash
Operating Temperature32 to 113°F (0 to 45°C)
Ports48 10/100/1000 Ethernet ports
Form FactorRack-mountable
Jumbo Frame SupportYes
Input Voltage100 to 240 VAC
Storage Temperature-25 to 70 °C
Relative Humidity10 to 90% non-condensing

Related product manuals