Cloos QINEO NexT - Page 36

36
9.1.7 Config - General - QWD .................................................................................................. 64
9.1.7.1 Config - General - QWD - QWD-B ............................................................................... 65
9.1.7.2 Config - General - QWD - QWD Push-Pull .............................................................. 66
9.1.8 Config - General - SD module ...................................................................................... 66
9.1.9 Config - General - Options ............................................................................................ 66
9.2 Config - Water monitoring ................................................................................. 68
9.3 Config - Compensation ........................................................................................69
9.4 Access rights .............................................................................................................70
9.4.1 Config - Access management ...................................................................................... 70
9.4.2 Config - User management and PAK (option) ...................................................... 72
9.4.2.1 Config - User management - Options ..................................................................... 74
9.4.2.2 Config - User management - User overview ........................................................ 75
9.4.2.3 Config - User management - User overview - PAK ............................................. 76
9.5 Config - Ethernet ....................................................................................................77
9.6 Config - Clock ............................................................................................................78
9.7 Config - Process monitoring ..............................................................................78
9.8 Config - General (2) ................................................................................................79
9.9 Config - General (3) ................................................................................................80
10. MAIN (2) - Diagnostics ............................................................................ 80
10.1 Diagnostics - Software versions ......................................................................81
10.2 Diagnostics - System logbook ........................................................................... 81
10.3 Diagnostics - Control ............................................................................................82
10.3.1 Diagnostics - Control - Ethernet ................................................................................. 83
10.3.2 Diagnostics - Control - I / O (inputs and outputs) ............................................. 83
10.3.3 Diagnostics VBC module ............................................................................................... 85
10.3.4 Diagnostics - Control - LED ........................................................................................... 86
10.3.5 Diagnostics - Control - Tandem .................................................................................. 87
10.4 Diagnostics - Process control ............................................................................87
10.4.1 Diagnostics - Process control - Pulse synchronisation ..................................... 88
10.4.2 Diagnostics - Process control - Current characteristic curve......................... 89
10.4.3 Diagnostics - Process control - Data set info ........................................................ 89
10.5 Diagnostics - Power unit ..................................................................................... 90
10.5.1 Diagnostics - Power unit - Mains ............................................................................... 90
10.5.1.1 Diagnostics - Power unit - Mains - Measured values ....................................... 91
10.5.2 Diagnostics - Power unit - Temperature .................................................................91
10.5.3 Diagnostics - Power unit - Calibration .................................................................... 91
10.5.4 Diagnostics - Power unit - Inverter ........................................................................... 92
10.5.5 Diagnostics - Power unit - Fan .................................................................................... 93
10.5.6 Diagnostics - Power unit - LED .................................................................................... 94
10.6 Diagnostics - Wire drive unit ............................................................................95
10.6.1 Diagnostics - Wire drive unit - MD ............................................................................ 95
10.6.2 Diagnostics - Wire drive unit - QWD-MD / QWD-A ........................................... 96
10.6.3 Diagnostics - Wire drive unit - QWD-B .................................................................... 97
10.7 Diagnostics - Cooling module ..........................................................................97
10.7.1 Diagnostics - cooling module - LED .......................................................................... 98
10.8 Diagnostics - Robot ................................................................................................99
11. MAIN (2) - Language .............................................................................100
12. MAIN (2) - Data backup ........................................................................101
12.1 Data backup Job ...................................................................................................101
12.1.1 Save job to storage medium ......................................................................................102
12.1.2 Load job from storage medium ................................................................................103
12.2 Data backup Config ............................................................................................104
12.2.1 Save configuration data to the storage medium .............................................104
12.2.2 Load configuration data from storage medium ...............................................105
12.3 Data backup Synergy ......................................................................................... 105
12.3.1 Save characteristic curve to the storage medium ...........................................105
12.3.2 Load characteristic curve data from storage medium...................................106
13. User log on/off .......................................................................................106
13.1 MAIN (2) - Log on ................................................................................................. 106
13.2 MAIN (2) - Log off ................................................................................................106
14. Job mode .................................................................................................107
14.1 Save job .................................................................................................................... 107
14.2 Overwrite an existing job ................................................................................108
14.3 Copy a job................................................................................................................108
14.4 Activate job ............................................................................................................109
15. Main (3) - Weld data monitoring .......................................................109