Cloos QINEO NexT - Block 3 PREMIUM operating module

35
Block 3 PREMIUM operating module
Contents
1. Main menu ............................................................................................... 38
2. MAIN - Synergy ........................................................................................ 38
3. MAIN - Operating modes ....................................................................... 39
3.1 2-cycle ..........................................................................................................................39
3.2 4-cycle ..........................................................................................................................39
3.3 Super-4-cycle ............................................................................................................40
3.4 Spot welding ............................................................................................................40
3.5 External .......................................................................................................................40
4. MAIN - process ......................................................................................... 41
4.1 Electrode .....................................................................................................................41
4.2 TIG .................................................................................................................................41
4.3 Speed Weld ................................................................................................................ 41
4.4 Vari Weld ....................................................................................................................41
4.5 Control Weld .............................................................................................................41
4.6 Syn off ..........................................................................................................................41
4.7 Cold Weld ...................................................................................................................42
4.8 Rapid Weld .................................................................................................................42
4.9 Rapid Pulse Weld ....................................................................................................43
4.10 MoTion Weld ............................................................................................................43
5. MAIN - Function ....................................................................................... 43
5.1 DuoPulse ....................................................................................................................43
5.2 CleanStart ..................................................................................................................44
5.3 Blow through ...........................................................................................................44
5.4 Threading (only in connection with MoTion Equipment) ...................44
5.5 Wire forward ............................................................................................................44
5.6 Wire backward.........................................................................................................44
5.7 Gas manually ...........................................................................................................44
5.8 Start manually .........................................................................................................45
5.9 Off / Re-start ............................................................................................................. 45
6. MAIN - Programming ............................................................................. 45
6.1 Parameters in the operating modes 2-cycle and 4-cycle ......................46
6.2 Parameters in the operating mode Super-4-cycle ................................... 47
6.3 Parameters in operating mode Spot Welding / Interval ......................48
6.4 MAIN - Programming - Setting ranges .........................................................49
6.4.1 Input of setting ranges................................................................................................... 49
6.4.2 Prerequisite to use the setting ranges .................................................................... 50
6.4.3 Deactivating the setting ranges ................................................................................ 51
6.5 MAIN - Programming - Tandem ....................................................................... 52
6.6 MAIN - Programming - Pulse synchronisation .........................................52
6.7 MAIN - Programming - Expert Mode .............................................................52
6.7.1 Expert Mode - Reset to synergy values .................................................................... 53
6.7.2 Main parameters in the "Expert Mode" .................................................................. 53
6.7.3 Secondary parameters in the "Expert Mode" ....................................................... 54
6.7.4 "DuoPulse parameters" in the "Expert Mode"...................................................... 54
6.8 Main - Programming - Active QWD ...............................................................55
6.9 Main - Programming - Welding circuit (from x.02) ................................55
7. MAIN - Measured values ........................................................................ 55
7.1 Operating data ........................................................................................................56
7.1.1 Data set switching 1/2 ................................................................................................... 57
7.1.2 Seam counter Setup ........................................................................................................ 57
7.1.3 Consumption costs .......................................................................................................... 58
8. MAIN - Display ......................................................................................... 58
9. MAIN (2) - Config (Configuration) ........................................................ 60
9.1 Config - General ......................................................................................................60
9.1.1 Display brightness ............................................................................................................ 61
9.1.2 MHW x10 Master .............................................................................................................. 61
9.1.3 Control coolant pump and fan ................................................................................... 61
9.1.4 Config - General - Basic settings ................................................................................ 62
9.1.4.1 Config - General - Basic settings - Tandem ............................................................ 63
9.1.5 Config - General - Basic settings (2) .......................................................................... 63
9.1.6 Config - General - Sense technology ........................................................................ 64