To Next PageTo Next Page
Need help?Do you have a question about the Codan HF SSB and is the answer not in the manual?
General| Brand | Codan |
|---|---|
| Model | HF SSB |
| Category | Transceiver |
| Language | English |
Lists related manuals and guides for further information.
Describes fixed base and mobile station types and transceiver versions.
Details mounting cradles and procedures for the transceiver.
Instructions for mounting control head and loudspeaker for accessibility.
Ensures 12V DC operation, covering battery or mains supply usage.
Explains essential grounding for efficient transceiver operation.
Lists connectable ancillary equipment and antenna considerations.
Procedures for creating and editing receive-only and transmit channels.
Steps to create transmit channels with new transmit frequencies using option TXE.
Creates receive-only channels by saving frequencies tuned in Free-Tune mode.
Procedure to delete unprotected channels from the transceiver.
Sets up any of the three scan tables with up to ten receive channels.
Procedure to delete any of the three scan tables from the transceiver.
Sets up the telephone directory for sending telcalls, holding ten entries.
Explains how to enter and navigate Setup mode for transceiver settings.
Details available Setup mode procedures with page number and setup code.
Explains the arrangement of Setup mode procedures in a menu tree.
Sets the transceiver's alphanumeric address for ALE calls.
Resets specific ALE option settings (0-16) to their factory values.
Changes how the Automatic Link Establishment (ALE) controller operates.
Changes the time interval between ALE sounding signal transmissions.
Changes the volume of beeps made by the transceiver (NORMAL, SOFT, LOUD).
Sets the length of the preamble transmitted at the start of a selective call.
Limits stations that can receive GPS, page, and status call information.
Calibrates the transceiver clock against an external standard for timing accuracy.
Sets the time and date of the transceiver's internal clock.
Copies settings from one transceiver to another via a cloning cable.
Adjusts the brightness level of the transceiver's display.
Adjusts the contrast level of the transceiver's display.
Switches the display of diagnostic information (signal strength, voltage) on or off.
Sets how the frequency is displayed for each channel (RX/TX, INHIBIT, RX ONLY).
Sets up the transceiver to receive emergency selcalls (DISABLED, RECEIVE-ALL, SELECTIVE).
Sets up the address and channel for sending emergency selcalls.
Switches the availability of Free-Tune Receiver mode for tuning.
Switches the display of GPS location data (latitude, longitude) on or off.
Switches the GPS timeout warning beep on or off.
Prepares and stores up to three messages for sending in a page call.
Enables options using a password, displays transceiver ID for agent contact.
Procedure to delete a forgotten PIN using a PIN deletion password.
Sets up a custom message displayed on transceiver power-up.
Selects the initial mute setting (NO MUTE, AUDIO MUTE, SELCALL MUTE) upon power-on.
Selects whether to display transceiver address on power-on.
Switches PTT release beeping on or off for transmission indication.
Sets time limit to prevent transceiver staying in transmit state by mistake.
Selects whether to recall channels by frequency or channel number.
Switches RF gain on or off to adjust receive sensitivity.
Identifies equipment connected to RS-232 or GP connectors on the rear panel.
Sets the speed of information transfer for connected equipment.
Sets time delay for resuming automatic scanning after a call.
Switches scan table editing on or off to protect scan table information.
Sets up addresses for the transceiver's five selcall groups (S1-S5).
Selects communication method for stations using addresses longer than four digits.
Switches selcall lockout on or off to prevent call interference.
Switches the availability of the selcall mute button on or off.
Switches the ability to send status calls (diagnostics, config, user) on or off.
Switches the ability to send telcalls on or off.
Sets high and low frequency pairs for four tone call groups (T1-T4).
Switches the ability to respond to 99-beacon calls on or off.
Explains how to enter and exit Link Setup mode by repositioning an internal link.
Controls output of switching signals for antenna and equipment based on frequency.
Procedure to set, change, or cancel the transceiver's PIN for security.
Switches the availability of Setup mode on or off to prevent unauthorized changes.
Resets transceiver settings, channels, or both to factory default values.
Details pin arrangements for microphone, antenna, remote control, GP, and other connectors.
Lists ancillary equipment and their rear panel connection methods.
Explains using the interface for connecting multiple devices like GPS and computers.
Lists technical specifications including channel capacity, frequency range, and dimensions.
Lists available accessories with their codes and descriptions for purchase.
