ComAp InteliLite NT AMF26-P

To Next Page

To Previous Page

InteliLite

AMF26-P-2.4 Reference Guide.pdf

3. Remove the small cover.

4. Break apart the small cover into two pieces. Do not throw away the smaller part!

Main Page

Table of Contents2
General Guidelines5
What Describes this Manual5
Important Safety Instructions5
Warnings5
Symbols5
Text5
Dangerous Voltage6
Adjust Set Points6
General Description7
Description of the Controller System (with All Options)7
What Is in the Package7
IL-NT RS232 Communication Module7
IL-NT RS232-485 Communication Module12
IL-NT S-USB Service USB Communication Module13
IB-Lite Ethernet Communication Plug-In Card14
Internetbridge NT15
IL-NT-GPRS GSM and GPRS Plug-In Modem15
IL-NT-AOUT8 Gauge Driver Module15
IL-NT RD Remote Display Software17
Il-Nt-Efcpm17
Il-Nt-Efcpm218
Remote Announciator IGL-RA1518
IG-IOM/PTM Module19
IG-IB Internet Bridge20
IL-NT Terminals and Front Fascia22
Installation23
Mounting23
Recommended Wiring24
AMF - Wiring Diagram24
Stand-By Applications25
Contactors (Set Point MCB Logic = "CLOSE-OFF")25
ATS with Two Stable Positions (Set Point MCB Logic = "CLOSE-ON")25
ATS with Three Stable Positions (Set Point MCB Logic = "CLOSE-OFF")26
Dual Mutual Standby (Dual AMF) Application26
Getting Started29
How to Install29
Power Supply Fusing31
Binary Output Protections31
Magnetic Pick-Up32
Current Measurement33
Earth Fault Measurement (Module)34
Technical Characteristics34
Voltage Measurement and Generator Connection Types36
Analog Inputs40
Recommended CAN/RS485 Connection44
Extension Modules (CAN Bus) Connection46
Connection Rules47
Inputs and Outputs48
Binary Inputs IL-NT - Default48
Binary Inputs - List48
Emergency Stop49
Remote off50
Start Button51
Stop Button51
Lang Selection51
Binary Outputs IL-NT - Default53
Binary Outputs - List53
Fuel Solenoid54
Stop Solenoid54
Cooling Pump54
Glow Plugs57
Fuel Pump57
Dummy Load58
Remote Connect65
Analog Inputs66
Analog Outputs66
Setpoints68
Password68
Basic Settings68
Comms Settings71
Engine Params74
Cooling Time76
Engine Protect80
Gener Protect82
AMF Settings86
Date/Time91
Sensors Spec92
Extension I/O92
SMS/E-Mail93
Remote Alarm Messaging93
Man Operations96
Restore Default96
Alternate Cfg97
Service Timers98
ECU-Controlled Engine Support101
Identifying Configured ECU102
Values Read from ECU103
Diagnostic Messages Read from ECU103
Analog Inputs103
Connection Description104
Engines with J1939 Support Started Via CAN Bus104
Cummins Engines with MODBUS Communication106
Background of the Sensor Calibration109
Default Sensor Curves109
Function Description110
OFF Mode110
MAN Mode110
AUT Mode112
TEST Mode113
Circuit Breakers Timing113
Relation between Mains Return and MCB114
Relation between GCB and MCB114
Alarm Management116
Sensor Fail (FLS)116
Warning (WRN)116
Breaker Open and Cooling (BOC)116
Shut down (SD)116
Mains Failure (MF)116
Voltage Phase Sequence Detection117
Gen-Set Operation States119
List of Possible Events119
History File123
Record Structure123
Init Screens124
Init Screen124
Info Screen124
Language Screen124
User Interface Screen124
Operator Interface AMF125
Display Screens and Pages Structure128
History Log128
Alarms129
Browsing ECU Alarms129
Earth Fault Protection Test129
Setpoint Change131
Entering the Password131
Controller Information Screen132
Display Contrast Adjustment132
Remote Control and Data Logging133
Direct Connection to the PC133
PC Software - Liteedit134
Modbus Protocol134
Remote Communication142
Internet Connection142
SMS Message Control142
Event Messages Description147
Recommended ISDN Modem148
Recommended GSM Modem148
Mobile SIM Card Setting148
Short Guide How to Start Using IL-NT-GPRS Module148
IL-NT-RD Remote Display Software153
General Description153
Warning153
IL-NT-RD Software Installation153
IL-NT-RD Wiring154
Connection Process154
Direct RS232 Connection154
Function Description157
SW Compatibility157
Maintenance158
Backup Battery Replacement158
Technical Data160
Inputs/Outputs Overview160
Generator Protections160
Language Support161
Power Supply162
Operating Conditions162
Dimensions and Weight162
Mains and Generator162
Binary Inputs and Outputs163
Analog Inputs163
Speed Pick-Up Input163
D+ Function163
CAN Bus Interface163
IL-NT RS232 Interface (Optional Card)164
IL-NT RS232-485 Interface (Optional Card)164
IL-NT S-USB Interface (Optional Card)165
IL-NT-AOUT8 Interface (Optional Card)165
IL-NT-EFCPM Interface (Optional Card)165
IL-NT-EFCPM2 Interface (Optional Card)165
Igs-Ptm166
Igl-Ra15166
Ig-Ib167

ComAp InteliLite NT AMF26-P - Page 9

Table of Contents

Related product manuals