263
(421) ......................................149
(422) ......................................149
(423) ..............................149, 150
(424) ......................................149
(511) ......................................150
(512) ......................................151
(513) ......................................152
(514) ......................................154
(515) ......................................154
(516) ......................................154
(517) ......................................154
(518) ......................................154
(519) ......................................155
(51A) ......................................155
(51B) ......................................155
(51C) ......................................155
(521) ......................126, 127, 155
(522) ......................................157
(529-52H) ..............................157
(531) ......................................157
(532) ......................................158
(533) ......................................158
(534) ......................................159
(535) ......................................160
(536) ......................................160
(541) ......................................160
(542) ......................................162
(551) ......................................162
(552) ......................................162
(553) ......................................162
(55D) .....................................163
(561) ......................................163
(562) ......................................163
(563-56G) ..............................163
(610) ......................................164
(6111) ....................................164
(6112) ....................................166
(6113) ....................................168
(6114) ....................................168
(6115) ............................168, 169
(621) ......170, 171, 172, 173, 174
(640) ......................................174
(641) ......................................175
(642) ......................................175
(643) ......................................175
(644) ......................................175
(645) ......................................176
(650) ......................................176
(711) ......................................181
(712) ......................................181
(713) ......................................181
(714) ......................................181
(715) ......................................182
(716) ......................................182
(717) ......................................182
(718) ......................................182
(719) ......................................182
(71A) ......................................182
(71B) ......................................182
(720) ......................................183
(721) ......................................183
(722) ......................................183
(723) ......................................184
(724) .......................................184
(725) .......................................185
(726) .......................................185
(727) .......................................185
(728-72A) .......................185, 186
(730) .......................................186
(731) .......................................186
(7311) .....................................186
(732) .......................................186
(733) .......................................186
(7331) .....................................187
(800) .......................................187
(811-81N) ..............................188
(8A0) ......................................188
(900) .......................................189
(920) .......................................189
(922) ...............................189, 190
33F .........................................126
Minimum Frequency .....................122
Modbus ...........................................75
Modbus/TCP ................................205
Monitor function
Alarm Select ............................148
Auto set ..................................147
Delay time ..............................145
Max Alarm ..............................145
Overload ...........................71, 145
Ramp Enable ..........................145
Response delay ........145, 146, 148
Start delay ...............................145
Motor cables ....................................33
Motor cos phi (power factor) ...........94
Motor data .......................................93
Motor frequency ..............................94
Motor I2t Current .........................196
Motor identification run ..................95
Motor Lost .....................................106
Motor lost ..............................149, 150
Motor Potentiometer .............132, 156
Motor potentiometer .....................156
Motor PTC ........................53, 54, 102
Motor ventilation .............................95
Motors ...............................................7
Motors in parallel .............................48
MotPot ..........................................121
Multi-motor application ..................90
N
Nominal motor frequency ..............128
Number of drives ...........................138
O
Operation ........................................89
Options ....................................57, 201
I/O Board ...............................204
Output chokes ...............................205
Output Voltage ..............................182
Overload ..................................71, 145
Overload alarm ................................71
P
Parameter sets
Load default values ................. 103
Load parameter sets from
Control Panel ......................... 104
Parameter Set Selection ............ 65
Select a Parameter set ............. 102
PI Autotune .................................. 134
PID Controller .............................. 135
Closed loop PID control ........ 135
Feedback signal ...................... 135
PID D Time .......................... 135
PID I Time ............................ 135
PID P Gain ............................ 135
Priority ............................................ 67
Process Protection ......................... 149
Process Value ................................. 181
Product standard, EMC .................. 10
Programming .................................. 85
PT100 Inputs ........................ 101, 102
PTC/PT100 board ........................ 204
Pump/Fan Control ........................ 138
Q
Quick Setup Card ............................. 7
R
Reference
Frequency .............................. 149
Motor potentiometer ............. 156
Reference signal ................ 89, 116
Set reference value .................. 116
Torque ................................... 149
View reference value ............... 116
Reference control ............................ 89
Reference signal ......................... 90, 91
Relay output .................................. 162
Relay 1 ................................... 162
Relay 2 ................................... 162
Relay 3 ................................... 162
Release speed ................................. 126
Remote control ............................... 67
Reset command ............................. 156
Reset control ................................... 91
Resolution ....................................... 88
RFI mains filter ............................... 33
Rotation .......................................... 92
RS232/485 .................................... 110
RTC- Real time clock .................... 205
RUN ............................................... 82
Run command ................................ 82
Run Left command ....................... 155
Run Right command ..................... 155
Running motor ............................. 123
S
Select Drive ................................... 138
Serial communication .................... 205
Settle Time .................................... 141
Setup menu ..................................... 85
Menu structure ........................ 84
Shaft power ................................... 181
To Next Page
Loading...
Need help?
General
