Endress+Hauser iTEMP TMT162 - Page 118

Index iTEMP TMT162
118 Endress+Hauser
HART output (submenu) ..................... 106
HART revision .............................103
HART short tag (parameter) .................. 101
HART® protocol
Device variables .......................... 29
Operating tools .......................... 29
Version data for the device .................. 29
L
Latitude (parameter) ........................105
Linearization (submenu) ...................... 96
Location description (parameter) ...............105
Location method (parameter) ................. 106
Locking status ........................... 74, 91
Longitude (parameter) ...................... 105
Lower range value (parameter) ............. 72, 100
M
Mains filter (parameter) ...................... 92
Manufacturer ............................. 113
Manufacturer ID (parameter) ..............103, 113
Max. update period (parameter) ............... 111
Measured values (submenu) ............... 88,
113
Measurement channels (display) ................ 92
Min. update period (parameter) ................110
Min/max values (submenu) ....................88
N
Nameplate ................................ 10
No. of preambles (parameter) ................. 102
O
Operating menu structure ..................... 25
Operating time ............................. 84
Operation options
Configuration programs .................... 22
Local operation .......................... 22
Overview ............................... 22
Operational state (parameter) .................. 81
Order code ............................ 87, 112
Other standards and guidelines ................. 60
Output (submenu) ..........................100
Output current ............................. 77
P
Polynomial coeff. A, B (parameter) .............. 97
Polynomial coeff. R0 (parameter) ................97
Previous diag n channel .......................86
Previous diagnostics ......................... 86
Previous diagnostics 1 ........................ 84
Process unit tag (parameter) .................. 105
Product safety ............................... 8
PV ..................................... 106
Q
QV ..................................... 108
R
Recalibration ...............................40
Reset configuration changed (Wizard) ........... 102
Reset device temp. min/max values (parameter) ....114
Reset sensor min/max values (parameter) ........ 114
Reset trim (Wizard) ................... 78, 96
, 101
Restart device (Wizard) ....................... 82
Return ................................... 43
RJ preset value (parameter) ................. 71, 93
S
Sensor (submenu) ........................ 75, 92
Sensor 1/2 (submenu) ........................93
Sensor lower limit ........................... 94
Sensor lower limit (parameter) ................. 98
Sensor max. value ........................... 89
Sensor min value ............................88
Sensor offset (parameter) .................. 75, 93
Sensor raw value ...........................114
Sensor switch set point (parameter) ........... 76, 98
Sensor trimming (parameter) .................. 95
Sensor trimming (submenu) ................... 94
Sensor trimming lower value (parameter) ......... 95
Sensor trimming min span .....................96
Sensor trimming upper value (parameter) ......... 95
Sensor type (parameter) ................... 69, 93
Sensor upper limit ...........................94
Sensor upper limit (parameter) ................. 98
Sensor value ........................... 88, 113
Serial no. sensor (parameter) ...................94
Serial number .......................... 87, 112
Setup (menu) .............................. 69
SIL (submenu) ..............................80
SIL checksum (parameter) ..................... 82
SIL option (parameter) ....................... 80
Simulation (submenu) ........................89
Software revision .......................... 104
Squawk (Assistant) ......................... 111
Start value (parameter) ....................... 99
Status signal (parameter) .................... 116
SV ..................................... 107
System (submenu) ...........................91
T
Terminal assignment .........................16
TV ..................................... 107
U
UL approval .............................10, 60
Unit (parameter) .........................69, 91
Upper range value (parameter) ............. 72, 100
V
Value 1 display (parameter) ....................79
Value 2 display (parameter) ....................79
Value 3 display (parameter) ....................79
Value current output (parameter) ........... 90, 115
W
Workplace safety ............................ 7