Endress+Hauser Proline Prosonic Flow P 500 - About This Document; Symbols in Documentation; Safety Symbols Explained

Proline Prosonic Flow P 500 HART Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 6
1.1 Document function ..................... 6
1.2 Symbols .............................. 6
1.2.1 Safety symbols .................. 6
1.2.2 Electrical symbols ................ 6
1.2.3 Communication-specific symbols ..... 6
1.2.4 Tool symbols .................... 7
1.2.5 Symbols for
certain types of information ......... 7
1.2.6 Symbols in graphics ............... 7
1.3 Documentation ........................ 8
1.3.1 Document function ............... 8
1.4 Registered trademarks ................... 8
2 Safety Instructions .................. 9
2.1 Requirements for the personnel ............ 9
2.2 Intended use .......................... 9
2.3 Workplace safety ...................... 10
2.4 Operational safety ..................... 10
2.5 Product safety ........................ 10
2.6 IT security ........................... 10
2.7 Device-specific IT security ................ 10
2.7.1 Protecting access via hardware write
protection ..................... 11
2.7.2 Protecting access via a password .... 11
2.7.3 Access via web server ............ 12
2.7.4 Access via service interface (CDI-
RJ45) ........................ 12
3 Product description ................ 13
3.1 Product design ........................ 13
3.1.1 Proline 500 .................... 13
4 Incoming acceptance and product
identification ..................... 15
4.1 Incoming acceptance ................... 15
4.2 Product identification ................... 15
4.2.1 Transmitter nameplate ........... 16
4.2.2 Sensor nameplate ............... 17
4.2.3 Symbols on the device ............ 17
5 Storage and transport ............. 18
5.1 Storage conditions ..................... 18
5.2 Transporting the product ................ 18
5.2.1 Transporting with a fork lift ........ 18
5.3 Packaging disposal ..................... 18
6 Mounting ......................... 19
6.1 Mounting requirements ................. 19
6.1.1 Mounting position ............... 19
6.1.2 Sensor set selection and
arrangement ................... 22
6.1.3 Environmental and process
requirements .................. 27
6.1.4 Special mounting instructions ...... 28
6.2 Mounting the measuring device ........... 29
6.2.1 Required tools .................. 29
6.2.2 Preparing the measuring device ..... 29
6.2.3 Mounting the measuring device ..... 29
6.2.4 Mounting the sensor ............. 29
6.2.5 Mounting the transmitter housing:
Proline 500 .................... 42
6.2.6 Turning the transmitter housing:
Proline 500 .................... 44
6.2.7 Turning the display module: Proline
500 ......................... 44
6.3 Post-mounting check ................... 45
7 Electrical connection .............. 46
7.1 Electrical safety ....................... 46
7.2 Connecting requirements ................ 46
7.2.1 Required tools .................. 46
7.2.2 Requirements for connection cable ... 46
7.2.3 Terminal assignment ............. 47
7.2.4 Preparing the measuring device ..... 48
7.3 Connecting the measuring device: Proline
500 ................................ 49
7.3.1 Connecting the connecting cable .... 49
7.3.2 Connecting the signal cable and the
supply voltage cable ............. 51
7.3.3 Integrating the transmitter into a
network ...................... 54
7.4 Potential equalization .................. 55
7.4.1 Requirements .................. 55
7.5 Special connection instructions ............ 55
7.5.1 Connection examples ............. 55
7.6 Ensuring the degree of protection .......... 59
7.7 Post-connection check .................. 59
8 Operation options ................. 61
8.1 Overview of operation options ............ 61
8.2 Structure and function of the operating
menu .............................. 62
8.2.1 Structure of the operating menu .... 62
8.2.2 Operating philosophy ............ 63
8.3 Access to operating menu via local display ... 64
8.3.1 Operational display .............. 64
8.3.2 Navigation view ................ 66
8.3.3 Editing view ................... 68
8.3.4 Operating elements .............. 70
8.3.5 Opening the context menu ......... 70
8.3.6 Navigating and selecting from list ... 72
8.3.7 Calling the parameter directly ...... 72
8.3.8 Calling up help text .............. 73