FlexDSL ORION 3 - RSTP DIAG> Command

User Manual LTU Orion 3
116
4.6.5.66 <RSTP DIAG> Command
The <RSTP DIAG> command shows RSTP diagnostics per interface. It displays what RSTP
priority and what MAC address switch receives and what MAC address / RSTP priority it
advertises to its neighbours.
CX_06_NET>RSTP DIAG
RSTP A 36864:00-0F-D9-04-A7-25 :
1. LAN1 32768:00-0F-D9-05-F5-BC
2. LAN2 36864:00-0F-D9-04-A7-25
3. LAN3 36864:00-0F-D9-04-A7-25
4. LAN4 36864:00-0F-D9-04-A7-25
5. LAN5 36864:00-0F-D9-04-A7-25
6. INT 36864:00-0F-D9-04-A7-25
7. WAN1 36864:00-0F-D9-04-A7-25
8. WAN2 36864:00-0F-D9-04-A7-25
9. WAN3 36864:00-0F-D9-04-A7-25
10. WAN4 36864:00-0F-D9-04-A7-25
11. MWAN1 36864:00-0F-D9-04-A7-25
12. MWAN2 36864:00-0F-D9-04-A7-25
RSTP B 32768:00-0F-D9-04-A7-25 :
1. MWAN1 32768:00-0F-D9-04-A7-25
2. MWAN2 32768:00-0F-D9-04-A7-25
RSTP C 32768:00-0F-D9-04-A7-25 :
1. MWAN1 0:00-00-00-00-00-00
2. MWAN2 0:00-00-00-00-00-00
RSTP D 32768:00-0F-D9-04-A7-25 :
1. MWAN1 0:00-00-00-00-00-00
2. MWAN2 0:00-00-00-00-00-00
RSTP E 32768:00-0F-D9-04-A7-25 :
1. MWAN1 0:00-00-00-00-00-00
2. MWAN2 0:00-00-00-00-00-00
CX_06_NET>
4.6.5.67 <PBVLAN [IF] [A..E]> Command
This command assigns the network interface (LANx, WANx, INT) to one of 5 port-based VLANS
(PBVLAN A..E).
CP_01_NET>PBVLAN LAN1 B
CP_01_NET>PBVLAN INT A
--------------------------------------------------------------------------------
New Network Configuration
--------------------------------------------------------------------------------
Ethernet settings : LAN1 LAN2 LAN3 LAN4 LAN5 WAN1 WAN2 WAN3 WAN4 INT
Access/Trunk : ACC ACC ACC ACC ACC Trunk Trunk Trunk Trunk ACC
Port-based VLAN : [B] [A] [A] [A] [A] [A] [A] [A] [A] [A]
VLAN : 1 1 1 1 1 1
QoS : 2 2 2 2 2 2
VLAN1 VID=1 : + + + +
VLAN2 VID=2 : + + + +
VLAN3 VID=3 : + + + +
VLAN4 VID=4 : + + + +
VLAN5 VID=5 : + + + +
VLAN6 VID=6 : + + + +
VLAN7 VID=7 : + + + +
VLAN8 VID=8 : + + + +
OTHER VLANS : + + + +
Speed : AUTO AUTO AUTO AUTO AUTO
System settings :
MAC address : 00:0f:d9:00:00:00
IP address : 192.168.0.254
Subnet mask : 255.255.255.0
Default gateway : 192.168.0.254
--------------------------------------------------------------------------------
Warning: New network configuration is shown, because it differs from running.
To view new network configuration, type 'NETCONFIG N'.
To view running network configuration, type 'NETCONFIG R'.
To apply changes in configuration, type 'APPLY VLAN' or 'APPLY ALL'.
Do not forget to 'CONFIRM' a good working configuration.
CP_01_NET>