FlexDSL ORION 3 - NETCONFIG [N;R;S;B]> Command

User Manual LTU Orion 3
108
IRATE [speed/OFF] [N=1-5]Set LAN port ingress rate limit
ERATE [speed/OFF] Set modem egress rate limit
CRATE [speed] [CoS] [WAN]Set COS egress rate limit
COS [QOS/VLAN] [N] [0..3/OFF]Set QoS/VLAN to COS mapping
SNMP [V1|V2C|V3] [ON|OFF]Activate support for SNMP v1, v2c, v3
TRAP [1/2] [IP/OFF] Set trap IP address or disable
TRAP [1/2] [V1/V2C] Select v1/v2c for trap
TRAP [1/2] V3 [RO/RW] Select v3 and user for trap
COMMUNITY Set SNMP v1,v2c community name
SNMPSET [ON/OFF] Enable/disable SNMP v1,v2c SET commands
SNMP [RO|RW] NAME Set SNMPv3 user security name
SNMP [RO|RW] AUTH [MODE] Set SNMPv3 user authentication: MD5,SHA,NONE
SNMP [RO|RW] PRIV [MODE] Set SNMPv3 user privacy: DES,AES,NONE
RMONALARM N [ON/OFF] Setup RMON alarm N
RMONEVENT N [ON/OFF] Setup RMON event N
LLDP [ON/OFF] Enable/disable LLDP
LLDP DEFAULT Set default LLDP setup
LLDP [PARAM] [VALUE] Set various LLDP transmission parameters
LLDP [TX|RX] [ON/OFF] Enable/disable transmission or receiving of LLDPDU
LLDP INT VLAN [ON/OFF] Enable/disable LLDP in managment VLAN only
LLDP CONFIG Show LLDP configuration
SNTP [1/2] [IP/OFF] Set/delete SNTP server IP addresses
SNTP TZ [+/-]HH:MM Set local time zone
DST SUMMER Set Summer time rule
DST WINTER Set winter time rule
DST [OFF/INFO/NAME] Select Daylight Saving Time
SYSLOG [1/2] [IP/OFF] Set/delete Syslog server IP addresses
NETDEFAULT Set default network configuration
SSH|TELNET|HTTP [ON/OFF] Enable/disable management servers
SSH PORT [N] Set TCP port for SSH service
SSL [SHOW/DEL] [options] Manage SSL certificate and private key
RADIUS [1/2] SECRET Set shared key for Radius Server 1 or 2
RADIUS [1/2] SECRET OFF Clear shared secret for Radius 1 or 2
RADIUS [1/2] TEST Test Radius server connection and User data
RADIUS [1/2] [IP:PORT/OFF]Set/delete IP address and port for Radius Server
RADIUS RETRIES [0..10] Set number of retries for both Radius servers
RADIUS TIMEOUT [1..5] Set Radius response timeout, seconds
SYSNAME [SET] Show/Set sysName variable
SYSLOCATION [SET] Show/Set sysLocation variable
SYSCONTACT [SET] Show/Set sysContact variable
STATUS RADIUS [NRSB] Show RADIUS server status and parameters
APPLY [ALL/GROUP] Apply changes to running configuration
CONNECT [N:[1-13/R]] Establish connection to remote unit
LINK [NN] Establish local connection
LINKCLEAR Exit all local connections
M Return to Configuration Management Menu
H Show available commands
-------------------------------------------------------------------------------
CX_06_NET>
4.6.5.52 <NETCONFIG [N/R/S/B]> Command
Without parameters the <NETCONFIG> command displays the running configuration of the
network subsystem and interfaces:
CO_06_NET>NETCONFIG
--------------------------------------------------------------------------------
Running Network Configuration
--------------------------------------------------------------------------------
Ethernet settings : LAN1 LAN2 LAN3 LAN4 LAN5 WAN1 WAN2 WAN3 WAN4 INT
Description : LAN1 LAN2 LAN3 LAN4 Backp WAN1 WAN2 WAN3 WAN4 INT
Access/Trunk : ACC ACC ACC ACC ACC Trunk Trunk Trunk Trunk ACC
Port-based VLAN : [A] [A] [A] [A] [A] [A] [A] [A] [A] [A]
VLAN : 1 1 1 1 1 1
QoS : 2 2 2 2 2 2
VLAN1 VID=1 : + + + +
VLAN2 VID=2 : + + + +
VLAN3 VID=3 : + + + +
VLAN4 VID=4 : + + + +
VLAN5 VID=5 : + + + +
VLAN6 VID=6 : + + + +
VLAN7 VID=7 : + + + +
VLAN8 VID=8 : + + + +
OTHER VLANS : + + + +