FlexDSL ORION 3

To Next Page
To Previous Page
  User Manual  LTU Orion 3 

 
PROGRAMMING GUIDE .................................................................................................. 57 
1  Command Structure ................................................................................................... 57 
2  Orion3 Software ......................................................................................................... 59 
3  Configuration and Application Storage ....................................................................... 59 
4  Groups of Commands Requiring Confirmation ........................................................... 61 
5  Command Syntax ....................................................................................................... 61 
6  Commands ................................................................................................................. 62 
6.1  Main Menu .......................................................................................................... 62 
6.1.1  System Invitation .......................................................................................... 62 
6.2  General Commands ............................................................................................ 63 
6.2.1  <H> Command ............................................................................................. 63 
6.2.2  <APPLY [ALL/GROUP]> Command ............................................................. 63 
6.2.3  <CONNECT N:1..13/R> Command .............................................................. 63 
6.2.4  <LINK [SN/00/FE]> Command ..................................................................... 63 
6.2.5  <LINKCLEAR> Command ............................................................................ 63 
6.3  Performance Management Menu ........................................................................ 64 
6.3.1  <H> Command ............................................................................................. 64 
6.3.2  <G826> Command ....................................................................................... 64 
6.3.3  <G826 Е1> Command ................................................................................. 65 
6.3.4  <ALLG826 N> Command ............................................................................. 66 
6.3.5  <RESETG826> Command ........................................................................... 66 
6.3.6  <RESETALLG826 N> Command ................................................................. 66 
6.3.7  <NETSTAT [LAN/WAN]> Command ............................................................ 67 
6.3.8  <NETERR [LAN/WAN]> Command .............................................................. 67 
6.3.9  <RESETNETSTAT> Command ................................................................... 68 
6.3.10  <LINKSTAT> Command .............................................................................. 68 
6.3.11  <LINKALARM> Command ........................................................................... 69 
6.3.12  <ALARMLOG [N]> Command ...................................................................... 69 
6.3.13  <LINKDIAG> Command ............................................................................... 69 
6.3.14  <M> Command ............................................................................................ 70 
6.4  Fault and Maintenance Management Menu ........................................................ 71 
6.4.1  <H> Command ............................................................................................. 71 
6.4.2  <NM> & <LINKNM> Command .................................................................... 72 
6.4.3  <STATUS> Command ................................................................................. 72 
6.4.4  <STATUS ETH> Command ......................................................................... 73 
6.4.5  <STATUS EXT> Command.......................................................................... 73 
6.4.6  <STATUS LLDP> Command........................................................................ 73 
6.4.7  <STATUS RADIUS> Command ................................................................... 74 
6.4.8  <STATUS DOT1X> Command ..................................................................... 74 
6.4.9  <STATUS ENCODE> Command ................................................................. 74 
6.4.10  <LOOP1 ON/OFF [N=1..4]> Command ........................................................ 75 
6.4.11  <LOOP2 [N:A/R] [ON/OFF]> Command ....................................................... 75 
6.4.12  <ALARM> Command ................................................................................... 75 
6.4.13  <AСO [GROUP ON/OFF])> Command ........................................................ 77 
6.4.14  <MACTABLE> Command ............................................................................ 77 
6.4.15  <LLDP STAT [IF/ALL]> ................................................................................ 78 
6.4.16  <STARTAL [N]> Command .......................................................................... 79 
6.4.17  <RESTART [N=1..4]> Command ................................................................. 79 
6.4.18  <RESET> Command.................................................................................... 79 
6.4.19  <CONFIRM> Command ............................................................................... 79 
6.4.20  <BACKUP> Command ................................................................................. 79 
6.4.21  <RESTORE> Command .............................................................................. 79 
6.4.22  <DIFF N/R/S/B N/R/S/B> Command ............................................................ 80 
6.4.23  <DUMP N/R/S/B> Command ....................................................................... 80 
6.4.24  <LOAD> Command ...................................................................................... 81 
6.4.25  <TLM> Command ........................................................................................ 81 
6.4.26  <TLM S [N:[Rnn-Rkk]] [ABC]> Command..................................................... 82 
6.4.27  <POWER DIAG> Command ........................................................................ 82 
6.4.28  <LOG> and [LOG C] Command ................................................................... 83 
6.4.29  <SOFTUPDATE> Command........................................................................ 83 
6.4.30  <TFTP [CMD] [ARG1][ARG2]> Command ................................................... 84 
Main Page
FlexDSL ORION 3 - Page 4

Table of Contents

Related product manuals
