Fluke 9500B - Page 207

Appendix A to Section 8: 9500B Maintenance — Error Reporting Subsystem 8-A3
Final Width = 215mm
ALWAYS: record the total message content for possible use by the Service Center.
-9001, “No calibration necessary for this function”
-9002, “Target factor is corrupt - select defaults”
-9008, “Edge speed outside limits”
-9009, “Restricted period for this amplitude”
-9010, “Maximum limit”
-9011, “Minimum limit”
-9012, “Outside amplitude range”
-9013, “Maximum amplitude for 50Ω load”;
-9014, “Outside frequency range”
-9015, “Outside amplitude range for DC”;
-9016, “Outside Period range”
-9017, “Outside deviation range”
-9018, “Deviation restricted by frequency range”
-9019, “Deviation restricted by amplitude range”;
-9020, “Syntax error”
-9021, “Outside numeric range”
-9022, “Only a restricted setting available”
-9023, “Maximum frequency for this waveform is 1.11MHz”
-9024, “Minimum highlight period is 20ns”
-9025, “No further display ranges available”
-9026, “No further options”
-9027, “Current probe accessory must be fitted to active head”
-9028, “Outside energy range”
-9029, “Entered number exceeds limits”
-9030, “Channel already in use”
-9031, “Outside skew range”
-9032, “VCO characterisation failed”
-9041, “Invalid number of divisions”
-9042, “Invalid units per division”
-9043, “Units per div, number of div’s combination outside range”
-9044, “Maximum units per division for 50Ω load”
-9050, “Printer is not responding”
-9051, “Printer out of paper”
-9053, “Previous test point failed - exceeded UUT spec. limits”
-9060, “Invalid test number”
-9062, “No more failures to view”
-9063, “No more tests to execute”
-9067, “Search procedure - NO test point”
-9068, “Search procedure - Function ID expected”
-9069, "Test .... must be executed first"
-9070, "Please wait - safety delay"
-9071, "Dual channel sine amplitude restricted to 2.78V"
-9072, "Dual channel sine amplitude restricted to 1.668V"
-9073, "Maximum frequency for 1M\352 load";3
-9074, "Selected head restricts frequency to 1.1GHz";
-9075, "Multi-channel DC requires 1M\352 impedance"
-9076, "Outside Pulse Width range"
-9077, "9560 Dual channel sine frequency restricted to 3.2GHz"
-7001, “Entry contains illegal characters”
-7002, “Entered value is outside the allowed range”
-7003, “Day entry is not a valid number”
-7004, “Day separator is incorrect”
-7005, “Month entry is not a valid number”
-7006, “Month separator is incorrect”
-7007, “Century entry is not a valid number”;
-7008, “Year entry is not a valid number”
-7009, “Year separator is incorrect”
-7010, “Month entry is not a valid month”
-7011, “Day entry is not a valid day”
-7012, “Hours entry is not a valid number”
-7013, “Minutes entry is not a valid number”
-7014, “Entry does not give a valid time setting”
-7016, “Bus address must be within the range 0 - 30”
-7017, “Safety voltage must be within the range 10V and 110V”
-7018, “Borderline value must be within the range 10.00 - 99.99%”
-7019, “Entry does not match previous password entry”
-7020, “New string contains illegal characters or values.”
-7024, “ WARNING Instrument near cal due date”
-7025, “ WARNING Instrument past cal due date”
-7026, “Ref frequency must be within the range 0.1 Hz and 1.3 GHz”
-7027, “Ref frequency must be within the range 0.1 Hz and 3.2 GHz”
-7029, “Ext Ref must be locked for selection to be allowed”
8.A.2.2.7 Device-Dependent Errors Reported only Locally on the Front Panel Screen
The error list for local operations, which are not reported to the remote operator, is given below:
Note that the error number will not be presented on the screen