EasyManuals Logo

HP ProCurve 5400zl User Manual

HP ProCurve 5400zl
765 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #459 background imageLoading...
Page #459 background image
encryption key to use for authentication with given server
(default is NULL). Specifying this key overrides the key set for
this server by the 'radius-server key <KEY-STR>' global
conguration command.
o key <KEY-STR> - species the global encryption key, which is
used for authentication if encryption key for the server is
not congured. The default is NULL.
o timeout <1-15> - server response timeout interval in seconds. The
default is 5 seconds.
o retransmit <1-5> - species the maximum number of retransmission
attempts. The default is 3 attempts.
o dyn-autz-port <UDP-PORT> - species the UDP port to listen for
Change-of-Authorization and Disconnect messages. The default
is 3799.
o dead-time <1-1440> - If the switch does not receive a response from a
specic RADIUS server, the switch avoids sending any new
authentication requests to that server until the dead-time has
expired. That is, during a new authentication attempt, the
switch bypasses a specied RADIUS server if a dead-time
period is running on the switch for a previous failure to
receive a response from that server. (The switch will still
send new authentication requests to any other congured
RADIUS servers that are not affected by a dead-time
condition.) For a specic RADIUS server, dead-time counting
begins with the end of the last timeout in the last retransmit
attempt of the failed authentication session. When dead-time
is set to 0 (zero), there is no dead-time and the switch will
not bypass a RADIUS server that has failed to respond to an
earlier authentication attempt. (Default: 0.)
COMMAND STRUCTURE
â–  [no] radius-server dead-time < Min | Max > -- Server unavailability time (default is 0, use the 'no'
form of command to set the dead-time to 0). (p. 459)
â–  dead-time < 1 to 1440 > -- Server unavailability time (default is 0, use the 'no' form of command
to set the dead-time to 0). (p. 459)
â–  radius-server dyn-autz-port < 1024 to 49151 > -- UDP port number to listen for
Change-of-Authorization and Disconnect messages (default is 3799). (TCP/UDP-PORT) (p. 460)
â–  [no] radius-server host -- IP address of the RADIUS server to use. (IP-ADDR) (p. 460)
â–  acct-port -- Accounting UDP destination port number (default is 1813). (p. 458)
â–  acct-port -- Accounting UDP destination port number (default is 1813). (TCP/UDP-PORT) (p.
458)
â–  auth-port -- Authentication UDP destination port number (default is 1812).
(TCP/UDP-PORT) (p. 459)
â–  key -- Encryption key to use with the RADIUS server (default is NULL). (ASCII-STR) (p.
460)
â–  auth-port -- Authentication UDP destination port number (default is 1812). (p. 459)
â–  auth-port -- Authentication UDP destination port number (default is 1812). (TCP/UDP-PORT)
(p. 459)
â–  acct-port -- Accounting UDP destination port number (default is 1813). (TCP/UDP-PORT)
(p. 458)
â–  key -- Encryption key to use with the RADIUS server (default is NULL). (ASCII-STR) (p.
460)
â–  dyn-authorization -- Enable/disable dynamic authorization control from this host. (p. 459)
â–  key -- Encryption key to use with the RADIUS server (default is NULL). (p. 460)
â–  key -- Encryption key to use with the RADIUS server (default is NULL). (ASCII-STR) (p. 460)
457© 2009 Hewlett-Packard Development Company, L.P.
radius-serverCommand Line Interface Reference Guide

Table of Contents

Other manuals for HP ProCurve 5400zl

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ProCurve 5400zl and is the answer not in the manual?

HP ProCurve 5400zl Specifications

General IconGeneral
BrandHP
ModelProCurve 5400zl
CategorySwitch
LanguageEnglish

Related product manuals