â– ip-addr -- IP address of the enahced web auth server. (IP-ADDR) (p. 35)
â– page-path -- Sets the path of the login pages to be found on the ewa server.
(ASCII-STR) (p. 42)
â– web-list1 -- Manage web authentication based network authentication on the device port(s).
([ethernet] PORT-LIST) (p. 57)
â– auth-vid -- Configures VLAN where to move port after successful authentication (not
configured by default). (p. 30)
â– web-authvid -- Configures VLAN where to move port after successful authentication
(not configured by default). (VLAN-ID) (p. 55)
â– client-limit < 1 to 32 > -- Set the port's maximum number of authenticated clients (default
1). (NUMBER) (p. 31)
â– client-moves -- Set whether the client can move between ports (default disabled - no
moves). (p. 31)
â– logoff-period < 1 to 9999999 > -- Set the period of time of inactivity that the switch
considers an implicit logoff (default 300 seconds). (NUMBER) (p. 36)
â– max-requests < 1 to 10 > -- Set maximum number of times the switch retransmits
authentication requests (default 3). (NUMBER) (p. 39)
â– max-retries < 1 to 10 > -- Set number of times a client can enter their credentials before
authentication is considered to have failed (default 3). (NUMBER) (p. 39)
â– quiet-period < 1 to 65535 > -- Set the period of time the switch does not try to
authenticate (default 60 seconds). (NUMBER) (p. 47)
â– reauthenticate -- Force re-authentication to happen. (p. 47)
â– reauth-period < 0 to 9999999 > -- Set the re-authentication timeout in seconds; set to
'0' to disable re-authentication (default 0). (NUMBER) (p. 47)
â– redirect-url -- Set the URL that the user should be redirected to after successful login
(default none), Specify url up to 103 characters length. (p. 48)
â– web-redirect-url -- Set the URL that the user should be redirected to after successful
login (default none), Specify url up to 103 characters length. (ASCII-STR) (p. 58)
â– server-timeout < 1 to 300 > -- Set the authentication server response timeout (default
30 seconds). (NUMBER) (p. 50)
â– ssl-login -- Set whether to enable SSL login (https on port 443) (default disabled). (p. 50)
â– unauth-vid -- Configures VLAN where to keep port while there is an unauthorized client
connected (not configured by default). (p. 53)
â– web-unauthvid -- Configures VLAN where to keep port while there is an unauthorized
client connected (not configured by default). (VLAN-ID) (p. 58)
COMMAND DETAILS
reauth-period (p. 47)identity (p. 35)accounting (p. 26)
redirect-url (p. 48)initialize (p. 35)active (p. 27)
secondary (p. 48)ip-addr (p. 35)addr-format (p. 27)
secret (p. 50)login (p. 36)addr-limit (p. 27)
server-timeout (p. 50)logoff-period (p. 36)addr-moves (p. 27)
ssh (p. 50)mac-based (p. 37)authentication (p. 27)
ssl-login (p. 50)mac-list1 (p. 39)authenticator (p. 28)
start-period (p. 51)max-requests (p. 39)authorization (p. 30)
supplicant (p. 51)max-retries (p. 39)auth-timeout (p. 30)
supplicant-timeout (p. 52)max-start (p. 40)auth-vid (p. 30)
suppress (p. 52)method (p. 40)clear-statistics (p. 31)
system (p. 52)mode (p. 40)client-limit (p. 31)
telnet (p. 52)network (p. 41)client-moves (p. 31)
tx-period (p. 53)null-username (p. 41)commands (p. 31)
unauth-period (p. 53)num-attempts (p. 42)console (p. 32)
25© 2009 Hewlett-Packard Development Company, L.P.
aaaCommand Line Interface Reference Guide
To Next Page
Loading...
Need help?
General