EasyManuals Logo

HP ProCurve 5400zl User Manual

HP ProCurve 5400zl
765 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #615 background imageLoading...
Page #615 background image
administrator.
o location ASCII-STR - Up to 48 characters. Description of the
switch location.
o community ASCII-STR - Enter up to 32 characters to name an SNMP
community.
o <manager|operator> - manager - the community can access all MIB
objects; operator (default) - the community can access all except
the CONFIG MIB.
o <restricted|unrestricted> - unrestricted - any MIB variable that
has read/write access can be set; restricted (default) - MIB
variables cannot be set, only read.
o IP-ADDR - Address of the network management station.
o [none|all|not-info|critical|debug] - The level of Switch
events that will generate a Trap to be sent: none - send no log
message; all - send all log messages; not-info - send each log
message that is not informational-only; critical - send
critical-level log messages; debug (reserved for Internal use).
o [IP-ADDR|loopback<0-7>|dst-ip-of-request] - Policy type used to
ll the source-ip address eld of the snmp response/trap pdu:
IP-ADDR - This ip address will be used while sending the
snmp response/trap pdu; loopback<0-7> - lexicographically min.
congured ip address on specied loopback interface will be
used while sending the response; dst-ip-of-request - destination
ip address passed in the request pdu will be send as the source-ip
address in the response pdu.
COMMAND STRUCTURE
â–  [no] snmp-server community -- Add/delete SNMP community (ASCII-STR) (p. 615)
â–  view < Operator | Manager > -- Add/delete SNMP community (p. 622)
â–  write-access < Restricted | Unrestricted | | ... > -- Add/delete SNMP community (p. 622)
â–  snmp-server contact -- Name of the switch administrator. (ASCII-STR) (p. 616)
â–  [no] snmp-server enable -- Enable/Disable SNMPv1/v2 (p. 616)
â–  traps -- Enable/disable event traps to be sent by the switch (p. 621)
â–  arp-protect -- Traps for Dynamic ARP Protection. (p. 615)
â–  auth-server-fail -- Traps reporting authentication server unreachable. (p. 615)
â–  dhcp-snooping -- Traps for DHCP-Snooping. (p. 616)
â–  dyn-ip-lockdown -- Traps for Dynamic Ip Lockdown (p. 616)
â–  link-change -- Traps for link-up and link-down. ([ethernet] PORT-LIST) (p. 618)
â–  login-failure-mgr -- Traps for management interface login failure. (p. 619)
â–  password-change-mgr -- Traps for management interface password change. (p. 619)
â–  port-security -- Traps for port access authentication failure. (p. 619)
â–  snmp-authentication -- Select RFC-1157 (standard) or HP-ICF-SNMP (extended) traps. (p.
620)
â–  extended -- Send traps for Extended Authentication failures. (p. 617)
â–  standard -- Send traps for Standard Authentication failures. (p. 620)
â–  [no] snmp-server host -- Define SNMP traps and their receivers (p. 617)
â–  address -- IP address of SNMP notification host. (IP-ADDR) (p. 614)
â–  community -- Name of the SNMP community (up to 32 characters). (ASCII-STR) (p. 615)
â–  events < None | Debug | All | ... > -- (p. 616)
613© 2009 Hewlett-Packard Development Company, L.P.
snmp-serverCommand Line Interface Reference Guide

Table of Contents

Other manuals for HP ProCurve 5400zl

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ProCurve 5400zl and is the answer not in the manual?

HP ProCurve 5400zl Specifications

General IconGeneral
BrandHP
ModelProCurve 5400zl
CategorySwitch
LanguageEnglish

Related product manuals