HPE FlexNetwork MSR3012 User Manual

317
chassis chassis-number slot slot-number: Specifies an MPU on an IRF member device. If you do
not specify this option, the command displays kernel thread starvation information for the global
active MPU. (Distributed devices in IRF mode.)
cpu cpu-number: Specifies a CPU by its number. (Centralized devices in IRF mode/distributed
devices in IRF or standalone mode.)
Examples
# Display brief information about the latest kernel thread starvation.
<Sysname> display kernel starvation 1
----------------- Starvation record 1 -----------------
Description : INFO: task comsh: 16306 blocked for more than 10 seconds.
Recorded at : 2013-05-01 11:16:00.823018
Occurred at : 2013-05-01 11:16:00.823018
Instruction address : 0x4004158c
Thread : comsh (TID: 16306)
Context : thread context
Chassis : 0
Slot : 0
Cpu : 0
VCPU ID : 0
Kernel module info : module name (mrpnc) module address (0xe332a000)
module name (12500) module address (0xe00bd000)
# Display detailed information about the latest kernel thread starvation.
<Sysname> display kernel starvation 1 verbose
----------------- Starvation record 1 -----------------
Description : INFO: task comsh: 16306 blocked for more than 10 seconds.
Recorded at : 2013-05-01 11:16:00.823018
Occurred at : 2013-05-01 11:16:00.823018
Instruction address : 0x4004158c
Thread : comsh (TID: 16306)
Context : thread context
Chassis : 0
Slot : 0
Cpu : 0
VCPU ID : 0
Kernel module info : module name (mrpnc) module address (0xe332a000)
module name (12500) module address (0xe00bd000)
Last 5 thread switches : migration/0 (11:16:00.823018)-->
swapper (11:16:00.833018)-->
kthreadd (11:16:00.833518)-->
swapper (11:16:00.833550)-->
disk (11:16:00.833560)
Register content:
Reg: r0, Val = 0x00000000 ; Reg: r1, Val = 0xe2be5ea0 ;
Reg: r2, Val = 0x00000000 ; Reg: r3, Val = 0x77777777 ;
Reg: r4, Val = 0x00000000 ; Reg: r5, Val = 0x00001492 ;
Reg: r6, Val = 0x00000000 ; Reg: r7, Val = 0x0000ffff ;

HPE FlexNetwork MSR3012 Specifications

General

Brand	HPE
Model	FlexNetwork MSR3012
Category	Network Router
Language	English

Summary

Ping, tracert, and system debugging commands

ping

Tests reachability of destination IP address and displays ping statistics.

tracert

NQA commands

NQA client commands

Configures NQA client operations, including factors, codec types, and data parameters.

NTP commands

SNTP commands

PoE commands

apply poe-profile

Applies a PoE profile to a power interface (PI).

SNMP commands

display snmp-agent community

Displays SNMPv1 or SNMPv2c community information.

snmp-agent community

Configures an SNMPv1 or SNMPv2c community.

snmp-agent target-host

Configures an SNMP notification target host.

snmp-agent trap enable

Enables SNMP notifications.

RMON commands

display rmon alarm

Displays information about RMON alarm entries.

rmon alarm

Event MIB commands

NETCONF commands

CWMP commands

cwmp enable

Enables CWMP.

EAA commands

action cli

Adds a CLI action to a monitor policy.

rtm cli-policy

Creates a CLI-defined EAA monitor policy and binds it to a Tcl script file.

Process monitoring and maintenance commands

display exception context

Displays context information for process exceptions.

display kernel deadloop

Displays kernel thread deadloop information.

display process

Displays process state information.

monitor kernel starvation enable

Enables kernel thread starvation detection.

Port mirroring commands

mirroring-group

Creates a mirroring group.

Flow mirroring commands

mirror-to

NetStream configuration commands

IPv6 NetStream commands

sFlow commands

Information center commands