To Next Page
M
mcintyrehowardSep 1, 2025
What to do if programmed scan does not stop on Icom Transceiver?
- BBryce PenningtonSep 1, 2025
If your Icom Transceiver's programmed scan doesn't stop, set [SQL] to the threshold point.
What to do if programmed scan does not stop on Icom Transceiver?
If your Icom Transceiver's programmed scan doesn't stop, set [SQL] to the threshold point.
Why doesn't the ANT switch function on Icom IC-7800 Transceiver?
If the [ANT] switch on your Icom Transceiver does not function, it may be because the antenna switch has not been activated. Set the antenna switch in set mode to “Auto” or “Manual.”
Why repeater cannot be accessed on my Icom IC-7800 Transceiver?
If you are unable to access a repeater with your Icom Transceiver, ensure the split frequency function is activated by pushing [SPLIT] to turn it ON. Also, check if the programmed subaudible tone frequency is wrong and reset it using set mode.
Why doesn't memory scan start on Icom IC-7800?
If the memory scan on your Icom Transceiver does not start, it may be because fewer than 2 memory channels have been programmed. Program more than 2 memory channels.
Why programmed scan does not start on Icom IC-7800?
If the programmed scan on your Icom Transceiver does not start, it is possible that the same frequencies have been programmed in scan edge memory channels P1 and P2. Program different frequencies in scan edge memory channel P1 and P2.
Why is the transmit signal unclear on my Icom Transceiver?
If the transmit signal from your Icom Transceiver is unclear or distorted, try setting [MIC] to a suitable position, as it might be set too far clockwise.
Why select memory scan does not start on Icom IC-7800 Transceiver?
If select memory scan does not start on your Icom Transceiver, designate more than 2 memory channels as select channels for the scan, because 2 or more memory channels have not been designated as select channels.
Why is the sensitivity too low on my Icom IC-7800?
If the sensitivity of your Icom Transceiver is too low, and only strong signals are audible, try these solutions: Ensure the antenna is properly connected to the antenna connector. Select an antenna suitable for the operating frequency. Manually tune the antenna by pushing [TUNER] for 1 second. Finally, deactivate the attenuator by pushing [ATT] several times to select 'ATT OFF.'
How to fix Icom IC-7800 if output power is too low?
If the output power of your Icom Transceiver is too low, try these solutions: Rotate [RF PWR] clockwise. Adjust [DRIVE] to a suitable position. Also, set [MIC] to a suitable position. Ensure you've selected an antenna suitable for the operating frequency. Finally, manually tune the antenna by pushing [TUNER] for 1 second.
Why is received audio unclear or distorted on my Icom IC-7800?
To troubleshoot unclear or distorted received audio on your Icom Transceiver, try the following: Ensure you've selected the correct operating mode. If the PBT function is activated, push [PBT CLR] for 1 second to reset it. If you're receiving a strong signal, turn OFF the noise blanker by pushing [NB]. Deactivate the preamp by pushing [P.AMP] once or twice. Finally, adjust the [NR] control for maximum readability if the noise reduction is activated.
General| Brand | Icom |
|---|---|
| Model | IC-7800 |
| Category | Transceiver |
| Language | English |
Key capabilities of the IC-7800 transceiver.
Description of controls and indicators on the front of the transceiver.
Details of connectors and ports on the back of the transceiver.
Specifications for the ACC connectors.
Explanation of indicators and readouts on the LCD screen.
Initial steps for setting up the transceiver.
Proper grounding procedures for safety and performance.
Essential connections for basic operation.
Connecting external equipment for expanded functionality.
Connecting external linear amplifiers.
Connecting devices for data mode operations.
Details on compatible microphones and their connections.
Procedure for initial power-on and CPU reset.
Selecting between the main and sub receivers.
Methods for tuning and setting frequencies.
Switching between different communication modes.
Adjusting audio output levels.
Steps and considerations for transmitting.
Detailed functions for Single Sideband operation.
Detailed functions for Continuous Wave operation.
Features for CW keying and memory operation.
Detailed functions for RTTY operation.
Detailed functions for PSK operation.
Detailed functions for Amplitude Modulation operation.
Detailed functions for Frequency Modulation operation.
Visualizing signal characteristics on a spectrum display.
Enhancing receiver sensitivity for weak signals.
Fine-tuning the receive frequency for clarity.
Controlling automatic gain for stable audio output.
Adjusting IF filter passband for interference rejection.
Simultaneously monitoring two frequencies.
Reducing impulse noise from sources like ignitions.
Eliminating unwanted beat tones and interference.
Enabling hands-free transmission via voice activation.
Automatic transmit/receive switching in CW mode.
Shifting transmit frequency independently of receive.
Transmitting and receiving on different frequencies.
Recording received and transmitted audio for a QSO.
Listening to recorded QSO audio files.
Recording custom messages for transmission.
Transmitting pre-recorded voice messages.
Storing and managing frequencies and operating modes.
Methods for selecting stored memory channels.
Saving new frequency and mode data into memory.
Temporarily storing frequencies and modes for quick recall.
Overview of available scanning modes.
Steps required before initiating a scan.
Controlling scan pauses based on voice detection.
Scanning between programmed frequencies.
Scanning through stored memory channels.
Detecting subaudible tones for repeater access.
Connecting and selecting antennas for operation.
Storing antenna configurations for different bands.
Using the built-in antenna tuner for impedance matching.
Setting the current date and time.
Configuring automatic power ON/OFF schedules.
Setting the timer for automatic transceiver power off.
Overview of the transceiver's programmable settings.
Adjusting audio tone levels for transmit and receive.
Configuring accessory connector functions.
Customizing screen appearance and indicators.
Miscellaneous system configuration options.
Managing settings on memory cards and USB drives.
Backing up transceiver settings to external media.
Restoring transceiver settings from external media.
Diagnosing and resolving common operational problems.
Checking antenna performance via SWR meter.
Procedure for replacing internal fuses.
Understanding transceiver protection system alerts.
Details on connecting and controlling via CI-V interface.
Comprehensive command table for CI-V operations.
Descriptions of data contents for CI-V commands.
Detailed technical specifications for the transceiver.
Receiver and antenna tuner specifications.
List of compatible optional accessories.
Overview of firmware update process and benefits.
Critical warnings and recommendations for firmware updates.
Steps and requirements before performing firmware update.
Procedure for updating firmware using a memory device.
Procedure for updating firmware via PC connection.
Guidelines for physical installation and antenna placement.
Compliance certifications for Radio and Telecommunications Terminal Equipment.
